Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello
I need to do SD Card with nRF52840-DK. I have referred (zephyr/example/subsys/fatfs) sample program, based on that I have made one new project and also made overlay...
Hello sir,
I was referred this link ( https://github.com/zephyrproject-rtos/zephyr/issues/29921 ) to do USB DFU on nRF52840-DK, but I am facing an issue in this code is...
Hi! I looked at the specifications, and it doesn't seem like this is listed as not possible, but it strikes me like it should not be possible, so I wanted to make sure. Looking...
Dear Nordic,
I am using the pre-build option to build always rebuild a file. This file is used to setup the date and time stamp of the build. I have done something similarly...
Good day,
I would like to start this thread by saying that I have been developing an application using the nRF52832 chip for several months, so far it has been a very difficult...
Hi,
I am beginner with nrf9160 and its SDK. I want to send data from nrf9160 to an external flash memory. To test it I wanted to start simply by sending hello_world(sample...
Hi,
I'm usgn Nrf528332, Softdevice s132_nrf52_6.1.0_softdevice
I Use secure_bootloader BLE secure_bootloader\pca10040_ble with the public key, and matched privet Ket...
I have installed the latest SDK 1.3.0 using the Toolchain Manager.
I would now like to open nRF Connect SDK Projekt and get the follwoing error:
I have added the CXX...
Hello
I have several questions regarding the UUID (Bluetooth):
If I create an application using your nus bluetooth service (ble_nus.c), should I change the NUS_BASE_UUID...
Hi, We are using the Thingy91, which is running the mqtt_simple (nRF SDK 1.4 and modem firmware 1.2.2) example, to push data direct to our AWS instance. Everything is running...
Hi,
I am trying to run the nRF9160 AWS IoT sample - https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/nrf9160/aws_iot/README.html on an nRF9160 DK...
Hello,
I am running such code deliberately, it is allocating the buffer flawlessly until the 10th run (102*10 = 1020). After that, it gives 4 from the allocation function...
OS: Mac OS Catalina
I installed build tools,nrf connect sdk, sesames, tool chain by following the instructions mentioned in "Getting started assistant" of nRF connect 3...
I'm trying to get an nRF52832 to connect to a Linux host with a BLE adapter. The Linux host is listening for connections via an L2CAP socket, as in the (simplified) code below...
I have python 3.9 installed. I can downgrade if that is the issue. I'll probably try that while I wait.
If I try and install "pip install nrfutil" it will succeed, but it...
