Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Using SDK 16.0.0 on an nRF 52840 board.
Managed to get a board into a state where it had only data pages and no swap pages, and therefore fds_init fails with the NO_SWAP...
I want to use nrf SPI driver for SPI flash implementation. For that want to send either SPI transmit or SPI receive at single instance to write or read flash address. But...
Version: Mac OS X 10.15.5 (19F101)
I'm using the nRF Connect app Getting Started Assistant and manage to get through most of it. However, when I use Segger to open up a...
Im trying to run http_client example in zephyr folder (ncs\v1.3.0\zephyr\samples\net\sockets\http_client). When i debug, the app run to fault, i dont know what fault but it...
Hello,
I am trying to use lua script language on nrf52840 board using SES to compile and load code.
I already compiled and load some ble tutorials on nrf52840 and it...
Hi,
I'm trying to use the CryptoCell-312. As I've seen until now, it is not supported by Nrf Connect SDK. Is there a way to use CryptoCell-312? Is it possible to access...
I am using nRF52840 with SDK16 building with armgcc and trying to intergrate buttonless OTA into my project.
App details:
Based on the ble_app_hrs_freertos example project...
Hi,
we are using nrf52832 in our product and it needs external storage 8MB.
Please suggest flash storage IC that has driver support in SDK by default or which has ready...
I've build a custom board with the nRF52840.
I've noticed that the current consumption of the LPCOMP is not ~0.5uA, as specified in the datasheet, but in my case, when I...
Hi every one, I am running light switch example (using SDK 15.2 and SDK for Mesh version 3.1.0 ) with some modifies in Server Node* ( node with has LIGHT ), this node have...
Hi
I am working on the application in which I wanted to initialize and uninitialize different services. I am using device information services to read manufacturer data...
Hello,
I want to use two UART interface in nRF52832 at the same time,but the nRF52832 just has one UART,the other i wish to build by simulation。
How can i simulate the...
Hi,
I bought an nrf52840 processor from Aliexpres. I made circuit print.
Circuit board connection with nrf52840dk is as in the photos. I am using segger as Ide. I...
Hi All,
I am trying to use the saadc example given in nRF5_SDK_17.0.0_9d13099\examples\peripheral\saadc.
I have built the project and now I want to read some values from...
dear all：
My device designed by nRF52840，it·s a central and peripherals at the same time .I have a problem about connect interval .My device as central need connect with...
