after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
as i mention in https://devzone.nordicsemi.com/f/nordic-q-a/44924/dfu-serial-failed i have f ramming error now and then when i do DFU over serial.
My idea was to write...
Hi,
after I received the thingy91 I wanted to connect it to the cloud, as mentioned in the get started.
But when I want to add the LTE Device, it shows the following Error...
Hi,
I got a new USB840M that have only the NRF52840 with a USB connector, I installed the nordic_cdc_acm.inf (driver for USB) for my PC, and my PC started to recognize...
Hello
I'm using the Development kit nRF52840, SDK 15.3.0, and the Sofdevice s140 6.1.1
I've created a BLE Battery client service, my implementation is extended upon the...
Hi Nordic DevZone,
I am currently trying to implement a system whereby a nordic nRF52 board scans and broadcasts in alternation, using freeRTOS tasks.
I have yet to...
When I tried building the Mesh 3.2.0 SDK on MacOS with cmake, I got link errors with the static libraries rtt and uECC.
The fix I discovered was to change the CMakeLists...
I am working on developing an application where the app layer tries to throw out messages if the message parameters are not valid. One the parameters to validate is a TID...
Hello, I working for TSS.se now selling 100.000 temperature-loggers annually. We aim to develop a new IoT based logger based on nRF52832 as a replacement.
Does following...
In order to compile against custom hardware, we changed overlay and dts files, but I cannot remember which. How do I find out?
I get the error
devicetree error: 'ss-pin...
I am using NRF52832 as Beacon, I want to classify the RSSI as High, Medium, Low, and Poor based on RSSI.
I am using SDK14.2.0 for Beacon and Gateway.
And using +4dBm Tx...
We are using Mesh SDK 3.2.0 and nRF52840 DK.
We wanted to use p_meta->p_core_metadata->params.scanner.adv_addr.addr as a unique identifier of the node hardware inside the...
After downloading and installing nrf mesh SDK as directed here https://www.nordicsemi.com/DocLib/Content/SDK_Doc/Mesh_SDK/v3-1-0/index . I'm not able to build any examples...
Hi, I am trying to use the RSSI viewer to scan RSSI values and verify the nearby beacons. But unfortunately RSSI viewer is NOT working and the following error message shown...
