Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions: ...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
I have a nRF9160-DK (PCA10090, 1.0.0, 2020.50) that I am trying to flash with the Modem Shell using the Quick Start app on a M1 Max MacBook Pro, running macOS 14.5....
Hello,
I am evaluating the nRF5340 for a potential BLE audio application. I was able to program the kit following the instructions and using the build script (or through...
I am running the nRF5340 Audio DK and trying to find a device with an app that scans BLE advertisements, but the device cannot be found.
I have confirmed that sound is being...
Hey guys, I'm trying to set the max tx power for our nRF52840 project and I'm getting this error:
CONFIG_BT_CTLR_TX_PWR_MINUS_1 was assigned the value y, but got the value...
I'm presenting an issue when exporting the data collected with the Power Profiler Kit 2 in the software (nRF Connect for Desktop v5.0.0), specifically the digital outputs...
Good afternoon,
I am debugging the nRF9160 in a product, and what we are noticing is that the socket "poll" events do not appear to be generated when the system is in...
If you look at the circuit of the PCA10040, it uses a 32Mhz 12pF crystal.
C1 and C2 of the crystal are 12 pF.
However, you say to use this formula: C1 = C_L * 2 - 4pF...
I am testing the current consumption of SIM cards with PPK2.
When PPK2 is connected to VCC ( voltage 1.8 v or 3 v ), the PPK2 can display the current properly ( around 9...
I am attempting to store a pre-generated key in the psa key store using the psa API. I have taken the nrf->samples->crypto->hmac and nrf->samples->crypto->persistent_key_usage...
Hi,
I am working on a setup where nRF5340 uses W5500 Ethernet IC and communicate MQTT over TLS. The actual setup for now is nrf5340dk + w5500 ethernet shield.
I am working...
We found one charging issue on nPM1100, after we assemble the battery to the PCBA, and then apply 5V to nPM110 (VBUS) and GND. The protection ciruit does not release, and...
Hi,
I am using nrf52840 and SDK-16.0. Our product is already in the market.
we added some extra features now. after adding this we are not getting application timer call...
I am working on a project where my hardware includes an array of LEDs. I want to run an LED pattern on the array during the DFU process. I have tried to find a solution for...
Hi,
I need to provide a clock signal of 4.9152 MHz to an external ADC.
Can the NORA-B106 module (that integrate a nRF5340) supply that signal by the Application Core M33...
I am developing a simple ble peripheral device that will measure temperature and humidity. For the most
part, it's working but I can't get the behavior I expect when enabling...