Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I am trying to configure Pin P0.09 as SCL pin for TWI. But I am not getting any results with this pin while I get data when any other GPIO pins are configured as...
SDK: 15.2.0
SoftDevice: s140 6.1.0
Hello,
I seem to keep finding conflicting information on how the NRF52 manages power to its peripheral devices and whether the application...
Dear proffesionals,
I am very beginer to nordic chip.i am using nrf_SDK_15.0.0_a53641a version.i am trying to integrate the writable_ndef_msg file to bluetooth.so how to...
Hello,
I am using custom hardware with an nRF52810 chip, connecting it to P16 connector of the power profiler kit. I use the power profile kit to check power consumption...
Hi guys,
I am a newbie in nRF but with some experiences in embedded systems . I have just been asked to work on a project that connects a nRF52811 to a nRF91.
I initially...
I'm testing a gps sample program below. github.com/.../gps
I have two questions about it.
1. It doesn't acquire NMEA data. it always stops working when it reaches 30 sec...
Hi
I tried to connect my dongle to PC but it is not getting detected , Even the red LED is not blinking., Can someone help me out with this issue
Thanks
Tabassum
I'm using LPCOMP to sense multiple input.
I call the lpcomp_read() function below for each input pin.
If I only call this function for 1 pin only, it worked fine.
For...
Hi,
I'm developing an application requiring multiple connections to several peripherals from a single central. I followed the instructions given here https://devzone.nordicsemi...
Does anybody know a quick and easy way to disable the radio functions in a soft-device application?
I want to measure and optimise the power consumption of all the other...
Hi
Can someone suggest me how can i erase the secure bootloader from nrf52840(Dongle),Because am unable to get "erase all" or "erase and write" option in nrf connect application...
Dear Nordic Team,
I can not flash my nRF52840 USB dongle with the nRF Connect Programmer application.
The window looks like this:
Erase / Read / Write functions...
Hi,
I am wondering how connection and scan interval work together when using multilink central device. I am starting scanning (scan interval and window 0x80) again after...
So, after using my Devkit and everything working OK as far as I can tell, I decided to order up a bare BT832XE module and place it on my PCB.
Flashed it with the same firmware...
Hi,
I recently received a NRF9160 DK from DigiKey in U.S. and having trouble doing anything! I am using iBasis SIM card and a the moment my whole experience is like this...
