Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
hi,everyone
when i test the mesh/example/dfu , it is upgrade scucessed,but when i combine it to switch_light example ,it was failed , it looks end the transfer too early...
Hi, there~
I'm trying to make my own bootloader and starting with the secure bootloader sample code.
The problem is the orignal bootloader, that is compiled with secure...
Hello,
Recently I started working on BLE. I need details with respect to BLE 5.0.
Below are the features of BLE 5.0
2x Range (With 2Mbps PHY)
4x Speed (With...
Hi,
I've created 3 PWM pulses via:
Which works when I'm not starting Thread (from the examples/thread/freertos_coap_server example)
But when I start Thread...
Dear Sir,
I am working on the following scenario.
I have BLE device ( SDK 15 and softdevice s132). It is advertising for specific duration.
There are different phones...
Hi,
I am working on a project where I am sending and receiving Encrypted string data from my phone with nRF Toolbox to the nRF52840 DK. The basic paring is established along...
I recently got past an issue with not connecting to the LTE network getting an nrf_cloud_connect failed: 60 and had things working yesterday. I had support for that issue...
Hey, I'm trying to connect a touchscreen monitor (10 finger) usb into a computer, get a raw input report and send it over uart to bluetooth module and sent it to other computer...
In IAR it shows the cycle count registers and they appear to work as expected in that view (shown as CYCLECOUNTER) . In the IAR Project/SFRSetup it shows the address of DWT_CYCCNT...
Hello,
I am developing a simple HID device with output report to receive data from PC. I took keyboard example as base project and I want to increase output report size...
Hello!
I have a custom nRF52832 board with an FTDI usb/serial part running my app successfully.
I generally program the board with a JLINK and SWD, but I am working to...
Hi, I apologize for the question renewal, that is the same as ticket "SDK15 DFU and WatchDog issue" (for my mistake I closed the discussion post!). I have developed a custom...
SDK 15.3.0
I want to save some user data in UICR , this data will change when application runing. How to re-write the data into UICR.
I assume that the UICR will not be...
Dear sir,
I have merged the twi_sensor code in ble_app_uart code in order to read the temperature sensor MAX30205 with NRF52832 send it over Bluetooth. But I am getting...
