Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi, I just started nRF52 DK from scratch and downloaded several things informed from infocenter like SEGGER, Keil and SDK, but have no background about these things.
The...
I am trying to understand the provisioning process as defined in the Bluetooth Mesh Profile v1.01 specification. In particular, I don't understand the following paragraph...
Some Examples discuss background DFU from application level, but those require bringing in IPv6 stack and TFTP client. Since we are planning to integrate DFU of our device...
I got nrf_cloud_connect failed: -111 error while running asset tracker demo.
I know that I need to flash certificate files according to my previous question: https://devzone...
It looks like the DK comes with a coin cell type battery and there seems to be a tab that can be pulled off to activate. However I don;t see any mention of this in the documentation...
Hello,
I am developing product on nrf52 with sd s112_nrf52810_5.1.0_softdevice. My application caused unexpected sd fault at adress 0x000089B2. I expect it to be something...
Hi all,
I am using my android ble application , but I don't manage to receive data sent from the application to the device ( nrf52840 )
I am using the ble_app_uart example...
Hi all, I got the requirement to actually know the path of a message from a client to server(s). Is it possible to add a few bytes of data until the message reaches the server...
Hi
I'm using NRF52840 + SDK15.0.0 and softdevice 6.0.0
I have joined two program one is ble_app_uart and other SAADC capturing ultrasound noise. (Saadc program works perfectly...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
I'm developing in a freeRTOS environment. One thread is sampling the ADC using PPI at 200Hz, which various other threads sample Sensors via SPI and finally I'm using the NRF_LOG...
Hi,
I'm designing custom PCB with nRF52832QFAA chip and after custom PCB population I can't make SWD to get working. In order to eliminate where the issue is I would like...
Hi,
I have RF-BM-ND01 (nrf51822) BLE4.0 module and i am programming it using nrfjprog tool. and i am using nrf SDK12 to program examples. i tried to flash softdevice S130...
I am using SoftDevice S132 v3.1.0 and I have a high priority application ISR that cannot tolerate being interrupted by the SoftDevice. The ISR occurs once every connection...
I'm trying to understand the limitations and configuration options for the mesh stack, in particular what happens when the mesh becomes busy.
From studying the code it appears...
