I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello,
I am working on example
nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c
pca10040\s132\arm5_no_packs/ble_app_uart_c_pca10040_s132...
Hello, I would like to know if there is any way to avoid bootloader start in secureDFU firmware transfer. All the checks on init file and control point are on the application...
My DFU is staying in the bootloader, even after successful download of the application package.
I have modified the secure bootloader for my custom PCB (removed the GPIO...
Hi,
I'm trying to get OpenOCD flashing to work on Windows using the FTDI 2232H adapter and an NRF52 target. I found this site:
https://www.allaboutcircuits.com/technical...
Hello,
I am trying to read multiple registers from a slave of i2c.
The values that I capture are the first value repeated in all the buffer.
The number of readed reg...
Hi,
I would like to use ping pong mechanism to prevent faulty application update on nRF52840. Is there a way to build a single image to run at 2 different addresses? How...
I have OSX Sierra, VMWare Fusion and Windows 7 available.
I do Arduino (Teensy) dev, staying on the OSX side.
I want to use the nrf52 chip as a MIDI over BLE conduit ...
Hello,
I have a PCB with a NRF52 powered by batteries. We need to be able to plug the batteries, then program the device and never remove the batteries.
We noticed, that...
I have a need for an interrupt to go off at a 4khz rate. For this, I am using a repeated App Timer (running off the 32k crystal).
Prior to adding this extra timer, we used...
I'd like to run the DK in at the lowest power in SYSTEM_ON mode.
It's my understanding that the ble_app_gzll example places the system in the "low power" SYSTEM_ON mode...
Hello Folks
I would highly apprciate if anyone can point me in the right direction here
After lot of consultation we imported a smal size shipment (of about 1000 nRF51822...
Connection_mode_with_1sec_Notification.jpg
In my BLE project I am using connected mode, and I found that the current consumption is very high ~190uA during idle mode. I...
