Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
While using nRF Connect, I encountered an error when attempting to enter Debug mode with RTT active. Here are my J-Link specifications and log details:
When I have...
Hi folks,
I am using zephyr sdk version 2.7.0 with a custom board that integrates a nrf52832, an ens210 sensor for temperature and humidity and lis3dh sensor for accelerations...
Hello,
using nrf5340 audio sample present in SDK v2.9.0, I can't hear anything from my nrf5340 Audio DK
I'm testing unicast_server scenario using a Motorola Edge 50 Pro...
I would like to know how efficient it is in terms of power to use UART via the async UART API. Does power consumption differ when its receiving data vs when it is idle? Also...
Hi,
I'm required by FDA regulation to have an SBOM for my project,
I found online that Nordic supports a sort of software bill of materials in the following link: Software...
Im using two Thingy:91 X, Toolchain is v2.9.0. I build and flash the dect shell example. I select build configuration thingy91x/nrf9151/ns. No other changes.
Both devices...
Hello,
Currently i would like to test my modem on TX continuous wave mode, for LTE-M. I'm using dev kit nrf9160dk, modem firmware version v1.3.6 and nrf SDK v2.7.0.
...
Hello everyone,
I'm experiencing an issue with the AWS IoT Sample on my nRF device . Although I've provisioned the necessary certificates and configured my project to connect...
Hello
I started developing a BT shell based app on the nRf52840DK board and then moved to a custom board.
In the overlay file, I've deleted every nRf52840DK node I could...
I would like to know which pins are available for nRF5340 on Thingy91 X on the debug board interface.
I was looking into PCA64165_Schematic_And_PCB.pdf and PCA20065_Schematic_And_PCB...
I would like to achieve TX-POWER control using GPIO mode GAIN control on the application core in SDK_VerV2.8.0, similar to how it was done in V2.3.0. Could you please tell...
Hello,
IDE - Visual Studio Code
SDK version - 2.9.0
Computer platform - Win11
I'm at the early stages of a project which first requires to send ~10K of data to the...
I'm encountering a build error when compiling a project with both Wi-Fi and the PSA Driver for CryptoCell enabled in nRF Connect SDK v2.9.0. The error occurs in crypto_mbedtls_alt...
