Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
I am programming the NRF51-DK on mbed compiler. I have compiled some code below for using an analog to digital converter. I was able to print a voltage measurement...
HI,
I am facing some serious issue in 51822. It consumes more power than 51422 on a same custom board. I am using same software for both with s130. Surprisingly the 51422...
I'm registering two p_storage modules, one allocates 3 blocks of 16 bytes (so one page to my understanding) and the other one 512kb ( 5 pages).
to my understanding,if I...
Hi everybody.
I am making an application using ANCS, I saw that the original ANCS application saves some data to flash memory via device manager module and the parameters...
Is there a way to get to an softdevice/radio event, which is generated every time an advertising packet is send? I need to set a pin in high state while sending a packet.
Hi,
In my application, I am using nus service with S110 V7.1.0 (nRF51822). I faced to one problem that the rx channel is set up to notify characteristic. In iOS (8.3),...
My question is while the application is running, how can I disable the NUS service to turn on the DFU service. This idea stems from this question: devzone.nordicsemi.com/...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I've testing a Raytac mdbt40 module and I'm running the ble uart example (sdk 9.0, gcc debug enabled, no gcc optimization) and no external 32khz crystal
I can scan and...
Hello,
i would like to update my SDK to SDK11, but i'm not sure that the pack installer in keil works..
What are the different versions of the pack?
I 've this one...
Hello All,
The compatibility matrix states that the sdk for rev 2 devices has been discontinued on version 6.1.
We have some other products with rev 3 devices where...
Hi!
I'm using nRF51DK with s110_nRF51_8.0.0 Soft Device and SDK_9.0.0.
My application reads ADC with frequency 500Hz (2 bytes of data from one sensor each read), and twi...
I am just wondering about the status of nrf52 support for the mbed platform (specifically as a yotta target).
I have seen a number of other threads on both the nordic side...