Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
I use direct input AIN2 pin battery 3.3v, the other pins are not connected to anything, I did not enter into ADC_IRQHandler,may ask about what the problem it
this is my...
Has anything changed with the Bluetooth LE in iOS 8? I have an ANCS library for Arduino ( https://github.com/robotastic/ANCS-Library ) that was working fine with iOS 7. I...
I'm trying to program nrf51822 via st-link and open ocd.
Here command:
openocd-0.8.0.exe -f interface/stlink-v2.cfg -f target/nrf51_stlink.tcl -c "program address".
...
dear all:
I have 2 kind of board that are PCA10006 and PCA10028,
but I find out the IoT example can't be run on PCA1006,
what are different between PCA10006 and PCA10028...
I have added the DFU service to our own project. Normal application updates work perfectly and even the update of bootloader and softdevice is fine.
In a new case we had...
I'm still newbie of BLE developer, and designing a BLE device based on nrf51822 (whose service uuid is partially used for identification of serial number).
Like nordic's...
We want to design our own custom USB Dongle for connecting our sensor board to a PC. Sensor board has a nRF51 chip using Gazell protocol to transmit sensor data and also softdevice...
I am using keil compiler. The nRF51822 stack succesfuly compiled and also i am created the hex.I don't have j-link programmer but i will try to download using Ulink2 can u...
I meet a trouble like this:
My colleague used " nRF51822 QFAAC0 1322AW " to make a product. The KEIL program "based on s110_nrf51822_5.2.1_softdevice.hex and nRF51 SDK...
When nrf51822 with 32KB RAM will available? If it is going to be delayed is it possible to get samples? (I like to try IOT SDK and with my PCA10001 the heap overflows.)
...
If I don't call nrf_gzll_set_base_address_0(...) or nrf_gzll_set_base_address_1(...) what address will it use?
Also, what is the default number of send attempts?
Hi, I purchased and received the pca100028/nRF51-DK on Friday (12/19).
I've upgraded to Keil 5.12, loaded the 7.10 sdk pack, loaded the radio_test_pca100028 example ( I...
Hi
The datasheet for nRF24le1 seems to describe two ways to find out if the TX buffer is full.
Register map 07, STATUS, bit 0, TX_FULL
Register map 17...
Hi all,
I'm trying to work on my MacBook Air on BLE. I'm running Windows 7 under VirtualBox and using the new Keil µVision5.
But my problem is that whether the nRF51822...
