Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi, We have an application where we need to predict drift between two nRF52833 systems in low power mode running from LFRC (low frequency RC oscillator). Section 5.4.4.4 of...
I am an embedded software engineer and have experience developing BLE devices with nRF5SDK, but this is my first time using Zephyr/NCS.
I am developing a USB dongle (nRF52840...
Hi,
I am developing a product based on the nRF9160 using the LwM2M client. I successfully have this working using PSK, but want to use X509.
I am calling lwm2m_security_set_certificate...
I'm migrating our project with custom boards from NCS 2.6.1 to 2.7.0, and I'm having a number of issues in the vscode extension (v2024.9.87):
The "Create a new board"...
Hi,
We are designing a USB Receiver based off the Nordic Proprietary Radio + ESB.
Do you have any reference designs for a PCB antenna which must be as small as possible...
Hi,
I'm getting an error when building the example temperature that says: Linking 'temperature_pca10040.elf' cannot open output file C:/Users/임선영/Documents/SEGGER Embedded...
Hello,
I am designing a LTE-M GNSS Tracker, that should also be able to scan for WIFI APs. I dont need to use LTE and WIFI at the same time, but rather like that:
Connect...
Hello,
I accidentally programmed BLE firmware onto my Power Profiler Kit 2 (PPK2) , and now the device is not recognized. Here's what happened:
I first opened the NRF...
hi support team,
customer had one problem about "AT%XCBAND=? "
fir st. Customer try to set catm and catnb systemmode together as below, i could not see the band17 in list...
Hi.
We are using NCS v2.6.0 in our application and migrating it to v2.7.0.
In v2.6.0 we have used child/parent image for MCUBoot. We are using the same application firmware...
Hello,
I know that maybe you won't be able to help but i'm giving it a try
I'm trying to use enc28j60 connected to a nrf52840. I saw these example https://gitlab.com/enc28j60driver...
Hi,
I am using a NRF9160. I would like to use nrfx_timer with a base frequency of 32MHz with the TXCO as clock source.
I saw in the documentation that timers use the base...
Hello DevZone community,
I have been using the lte_lc_conn_eval_params_get() function in my application, which is executed periodically.
However, I'm encountering an error...
Hello,
My goal is to combine the Peripheral UART sample code and the LSM6DSO I2C sample code with the objective of sending data from the sensor over bluetooth. Based on...
