Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hi Nordic Semi,
Instead of using NRF52 for previous projects, I am new in NRF54L15 and zephyr.
I have started the blinky pwm sample in VSC and tried a lot to just...
Hey
Do the hardware in the NRF5340 support what is needed for Bluetooth classic.
I do know that there are no software support and no plans for supporting it, but if...
Dear DevZone support,
I'm currently evaluating nPM1300 for Lithium Polymer battery management and charging and would like to ask a question.
I understand that I can...
The documentation for the QoS dynamic parameters command "+CGRQOSRDP" specifies that the uplink and downlink maximum bitrates are in units of kbps, with a maximum value of...
Hello,
we are using the direct test mode example of NCS with an nRF5340.
Now we got a question from the testlab, about the transmit power parameter.
The setting in...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hello. I am using vscode. I added sdcard to broadcast_sink in the existing samples in applications/nrf5340_audio and checked the list with the serial monitor and wanted to...
We want the system to be in low power mode in idle state. Therefore after advertisement is sent the BLE is switched off using bt_disable. The return for this function is fine...
Hello, I am using peripheral uart as my base project and uppn that, I have built my application.
I am delibrately changing the flash region just to see if i can modify flash...
Hello, I can commission nrf52840 bulb by iPhone successfully using below QR code:
https://project-chip.github.io/connectedhomeip/qrcode.html?data=MT%3A6FCJ142C00KA0648G00...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
I am trying to make a FOTA to update the firmware of the nrf9151 using the command AT#XFOTA, the issue I am having is that I am unable to have the app_update.bin file generated...
Hello, I am currently working with NRF5340-DK dev kit and I want to use 2 SPI devices connected on the same SPI bus OR use 2 different SPI instances, however none of these...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
