Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi all!
I am working on the SDK 15.2, with S132 6.0, and i use the SES IDE.
I have created a custom service with 32 characteristics for now. The goal in the future is...
Hello All,
I want to write codes for all the peripherals like GPIO , GPIO with Interrupt ,UART ,UART with interrupt , I2C , SPI , All Timers..without using the drivers provided...
Hey! I am testing some power consumption of my application, and I need to have a long rest period of appr. 15 minutes. I'm using an RTC timer in System ON sleep mode, full...
I have made a bluetooth beacon based on nRF52832 chip. I am able to write code DeviceDownload\nRF5SDK17009d13099\nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_beacon...
Can i use 2 nos NRF52832 BLE chip on single PCB , PCB size is 30x50 mm ,
1 chip for scanner
2 for advertising
3.If yes what is the position for antenna of both Chip...
Dear technical support.
We are using this chip (nRF52832) in our hardware.
I'd like to check is this feature AoA(part of BLE5.1) enabled in the chip?. Is there any application...
We are designing a people location tag for building workers. Bluetooth direction finding AoA/AOD is good for the application. Is there any development broad for Bluetooth...
There is a potential for the NRF_MESH_ASSERT(m_reliable.next_timeout_index < ACCESS_RELIABLE_TRANSFER_COUNT) to fire on line 170 of access_reliable.c if the following conditions...
Hello,
I am trying to install the pc-ble-driver-py for my buildroot arm-board.
After some struggle I was able to compile the pc-ble-driver for it, however the python tool...
Hi guys,
I am working on my project and until now I enabled the device to measure the voltage and get the sensor data from the temperature sensor which I need now to send...
Hello,
We have been using FDS in our nrf52832 based product. Recently we had a need to port application to nrf52810. It required some flash memory optimization. Fortunate...
Documentation states “When a connection is created it will inherit the transmit power from the initiator or advertiser leading to the connection.” In my BLE event handler...
Hi,
SDK16
I'm using ble_cus.c to define custom BLE service.
In the ble_cus.h file the definition of the UUID is
#define CUSTOM_SERVICE_UUID_BASE {0xBC, 0x8A, 0xBF...
Using just the nRF Connect SDK, I cannot get a push button to interrupt the NET CPU on the nRF5340DK.
I have the following code on the APP CPU:
nrf_gpio_pin_mcu_select...
