Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I recently updated my nRFConnect version to 2.2.1, which alos updated my Command Line Nordic tools. After this update, nRFConnect is " Unable to read connectivity firmware...
I am using a tab with some application in which if we kill the app ble_disconnect will happen and led will blink means it goes from connected to diconnected state.
path...
In the Light Switching example the Health model is used, but is it mandatory to used this model for Bluetooth Mesh applications or I can choose not to use it if i don't deem...
Hi everyone,
We're using our own customized BLE service with nrf51 on the one side and Android Smartphone on the other.
While connecting to the GATT I'm getting Error...
Forgive me if this is a stupid question, but I am new to programming microcontrollers other than Arduino and SPI in general.
I have a DAC that has a 16-bit register and...
Hello,
I am using 10 bit ADC read VDD voltage convert into mv without using any external voltage divider circuit, as per following function:
static void adc_configure_battery...
I'm embarrassed to say that the loopback I2S example, while able to show me that data can be sent and received through I2S, wasn't enough to help me achieve a simple demonstration...
Hi:
I am using SDK14.0 S132 for nrf52832 , i found it's sleep mode power comsumption large than 5mA .
I am using internal LDO and external power is 3.7V li-battery cross...
Hi
Just to be sure: I've recently bought the nRF52840 Preview DK (dev board for nRF52840) but I think I'm going to use the nRF52832 instead for my project.
Is it ok to...
Hi i want to create a new project in Eclipse. I did this my following the complete code form git hub for devzone.nordicsemi.com/.../
*Nordic has provided sample code for...
Hi!
I've based a new project for the nRF52840/S140/Preview-DK on ble_central/ble_app_uart_c .
I use the NRF_LOG_XXXX macros for debug and they print fine in RTT Viewer...
Hi,
I have two nrf51822 device, on work as GAP Central, another work as GAP Peripheral.The two device use different connection parameters, after the connection is established...
hello,
i have developed one board using nRF52832-QFAA and trying to dump simple LED blinking code in it using nRF52 DK board. But code is always dumping into custom board...
