after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Thank you very much for your answer!
Now I have another question,I'd like to convert the acceleration sensor (MMA8451) acquistion of data via bluetooth to the phone,I don...
I'm stuck in the Puck Central Tutorial, I have the zip from GitHub but can't seem to get any project to open.
Completed OK:
I completed the Puck Toolchain and Location...
I am right that:
a) once started the watchdog, it is not possible to stop the watchdog from the application
b) once started the watchdog, it is not possible to reconfigure...
I have successfully gotten the DFU to work on the NRF51422 S310V2.2 softdevice. I can download blinky app via the nRF Toolbox DFU application and all works great, but when...
Hi.
I am new to this forum, and can be described as a programmer with very little embedded experience.
I have bought a nRF51822 BT SMART BEACON KIT, and are trying to...
Hello,
i would like to turn off a sensor completely when unused and thought of powering it through the GPIO of the Controller.
I wondered if it is recommended or do the...
We have updated multiple android phones to nRF Toolbox for BLE app and we are all getting "Unfortunately, nRF Toolbox has stopped." error message when opening the app. nRF...
Hi,
I want to get a notification when the BLE event is started, in order to start a timer just after.
How can I get that?
I want to clarify my question :
My board...
I use the NRF 24AP2E in my communications, and I need detect if the communication is good.
I active the RSSI message, but in scanning mode I don't receive byte 0x20 in Measurement...
Hi All,
I am designing a circuit with nrf51822 and mcp25625 (microchip spi can interface). mcp25625 has an internal 16mHz xtal clock circuit and a digital clock out, I...
Hi, i'm kinda a newbie on this, and i'm trying to port the SDK available for arduino to a PIC, i followed the instructions on the SDK and also here
Now i want to verify...
I ran into an issue recently of attempting to make a pstorage_update call from the callback set in pstorage_register . It resulted in a difficult to track down error, so I...
I have a USB dongle of nRF24LU1p and it is identified as the Basic Remote firmware with a VID:PID of 1519:002B. I would like to reprogram it over USB but do not know how to...
