Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
When using the Serial Monitor, sending AT commands does not show any response from the Actinius Icarus board (nRF9160) Is there any way to resolve or debug this issue further...
Issue Description
The application starts successfully, initializes the modem library, connects to the LTE network, resolves the MQTT broker's address, and establishes an...
Hi,
Just wanted to know if nrf5340dk supports for UART baud rates until 512kbps.? And specific baud rates configuration like 122800.? If yes, is it simply configured as...
Body: Hello, I am using the Nordic Thingy:52 device, but it is not showing up as a port when I connect it to my system. Could you please help me troubleshoot this issue? ...
Hi,
I am using the MDBT42Q module of NRF2832 BLE Module unfortunately i have missed an inductor in my schematics could someone explain me will it work with out the inductor...
~Using nrf Connect sdk and toolchain at version V2.9.0 Attached is the app.zip project.
Basically it consists of a single main funct that prints ("AAAAAAAAAAA") to the...
Hi
I'm working on a nrf54L15DK to connect to windows 10. But the nrf54L15DK can't connect to windows 10.I am using the sample (C:\ncs\v2.8.0\nrf\samples\bluetooth\peripheral_hids_keyboard...
I am testing out the Bluetooth Channel sounding sample with the nRF54L15-dk board using the samples of Channel sounding Initiator with ranging requester. How to change the...
I was trying out the led_strip example in the zephyr samples on my nrf52dk/nrf52832 board with a single external WS2812B neopixel led connected at P0.23 , using the WS2812B...
Hello,
I am currently working in a wearable device based on the nRF5340. We have a few Audio DKs and I am using them as a hardware design reference.
I have a question...
I'm using the BLE mouse example, and the problem I'm having is if I remove the pairing/bonding information from the device, Windows will keep trying to pair with the device...
Hi, I am using zephyr and have created a custom DTS for nrf52840 soc. I am using SIM7070G and have created a custom driver for it which is located in (zephyr/drivers/modem...
Hi,
This string is defined by "CONFIG_BT_DIS_FW_REV_STR". Is there any API that can modify it?
Currently version management is done through VERSION files, but its display...
I attempted to flash the Matter lock example to my custom board, but the MCU shows no activity.
Back in v2.6.1, I used the following configuration, which worked.
How should...
Hello, I would like to know if the TX power used in the Zephyr examples "peripheral_uart" and "throughput" is set to 0 dBm? Is it true that for all Nordic examples, as long...
