Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Looking for Android logging utility where host processor on a Mobile device is interacting with nRF52810 over UART interface.
or Provide a stand alone logging utility that...
where can i search whta the mean about <type>,<result>,<datatype>,,<qos>,<retain>.....Etc.
EX: #XMQTTEVT: 4,0
I Don't know what these values represent
thanks
...
Hi,
We're using a 51422 with s130 to perform OTA DFU.
Both bases for bootloader and central are from sdk 12.2.
We have already implemented the older DFU (non-secure...
Hi,
I want to use the Code Profiling feature from Ozone with my nRF 52840 DK and the j-Trace Pro Cortex. Compiling and debugging my program works flawless inside Segger...
I am trying to figure out how to use the TX part of the BLE NUS Service to send a notification. Currently I am receiving data via the nus_data_handler, however because i will...
Hi, I just got my nRF5340 PDK and was wondering if it is possible to develop applications for the nRF5340 PDK in the Keil IDE?
I have been reading on the site and trough...
Normally with Segger Embedded Studio if you want to do a command-line build you use embuild.exe instead of emstudio.exe and away you go.
However, the NRF Connect/Zephyr...
Hi
We searched a lot of stuff regarding FOTA update in nRF52840DK using Lwm2m and coap protocol. But we could not get help in the right direction. We could not find any...
Hi,
We are using today SDK 15.0 and are upgrading to SDK 17.0 for development of our system.
In our application, we use BLE communication.
While comparing SDK_config...
I'm now using HX711 50kg sensors to build a scale
Now I can read the data from HX711, and try some method from internet, but still can't get the real weight
does anybody...
KeyWords: nRF52832 ESB Flash as EEPROM SDK:17.0.0
Hello, I an using nRF52832 developing ESB communicution with other nordic product.
I need to save some infomation, so...
Hi,
I got today a sample of your Nordic Thingy 91 device. I like to integrate the device into our IoT Data Provisioning Service from IoT Creators (Deutsche Telekom IoT...
Hi Everyone
I am able to write and read to and from QSPI memory interfaced with nrf52840 PDK.
I am using Segger Embedded Studio with sdk15.0.
I want to create a text...
If I write a value to ERASEPROTECT.DISABLE -- which itself works, as I'm fully able to perform the mass erase by writing the same value using the debugger -- I can't seem...
Hi,
We are using NRF52833 as a BLE central in our latest product and is undergoing radio certification tests. We are using SDK16 Radio Test example for the tests.
...
