after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I started debugging a device with an nRF52820 chip and found that the pinout is similar to nRF52833.
The test application was switching pin P0.15, but the ripple...
I'd like to order a debug in/out cable for the debugger (P18 & P19) on DK.
But I don't know what is the cable or the compatible sockets.
please let us know what is the...
We are using the following.
Module: BM833 (nRF52833) from Fanstel
Softdevice: S140 7.0.0
SDK: nRF5SDK17009d13099
Sample code: nRF5_SDK_17009\examples\ble_peripheral...
Hi,
I am a new comer and I try to customize samples/hello word projet
I am using nrf Connect v3.4.2 on Windows.
I try to perform a basic AES operation in main.c (based...
i am using nrf52840 DK. We have dedicated pins for say QSPI, UART, etc. but if I want to connect external flash memory i.e W25Q16 to the board, to which pins I should connect...
Hello Nordic team
I am working on nRF52832 dev board and I have a requirements to encrypt and decrypt data using AES-128 ECB . Could you please provide the example code...
The device was working well for around 2 weeks and was able to program it via SES, but now on connecting USB cable to the USB Connector (J2) with SW9 at VDD, no LEDs pulsate...
Hello
I am using the experimental_ble_app_uart for s110. I want to use the sd_temp_get() and convert the temperature value to a uint8_t, but if understand correctly when...
Current I used nRF52840 Dongle to develop a Bluetooth PC Tool base on nrf_ble_driver_obj_sd_api_v5 which shared on https://github.com/NordicSemiconductor/pc-ble-driver/blob...
hi,
I am done with general vehicle diag code. now, i need to interface with kwp via uart in nrf9160 controller.
please, suggest some ideas.
Thanks in advance ...
I just bought nrf52840 and J-link V9.
I look at start nrf52840 blinky.
website:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0...
I want to read ADC values from AIN2 (P0.04), and AIN3 (P0.05) channels of nrf52805. I am using S112, and I have the following code found in the internet.
float readADC(uint8_t...
Hi,
I want to build up a test software to test our product.
I find out pc-ble-driver that might be conformed our requirement and follow up below link to set up environment...
Hello, everyone.
I am using sdk v17 and I am looking into timer. I used the app_timer simply, but I don't know the nrf_drv_timer because I've never seen it before. Can...
