Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
I'm porting a working SPI camera demo from nRF52840 to nRF54L15 and I'm stuck with an issue where the SPIS RX amount is correct, but the received buffer is all zeros...
I have worked a bit with ESB and see that there are functions to get/set a channel, as well as check the RSSI value in the "struct esb_payload" for a packet. Are there already...
Hi, I am using NCS v2.9.0.
I am using sysbuild to build MCUboot and application images. Following are relevant Kconfig options:
mcuboot.conf
CONFIG_MAIN_STACK_SIZE...
Hi, having a little of an issue and would appreciate your support:
When bringing up a board which has the nRF9131 and the nPM6000 I'm getting the following error when doing...
Hello,
Currently working with NCS v3.10 and using SMP service with external flash to store image in a custom board. I'm capable of upload zipped application using DFU button...
I am using the nRF9151 DK, using the Serial LTE Modem firmware from the nRF Connect quick start.
I am planning to use nRF9151 as a serial modem, and connect it to my Host...
Hello
I was attempting to update a pre-production project where we have 2 servers connected to one gateway where the servers send the audio data back to the gateway with...
Hey guys, I want to store sensor data as circular buffer in non volatile memory. I saw https://docs.nordicsemi.com/bundle/zephyr-apis-latest/page/group_file_system_storage...
If a heartbeat or other chunk reliant on symbol file data is ingested when there is no symbol file associated with the Software Version / buildID it seems like the chunk is...
Hello,
I am currently trying to make an application that can do FOTA and store the secondary firmware image on an external flash using sQSPI. The project I started is based...
Hello,
We use the nrfx spis driver for communication between a ST processor (master) and a Fanstel BT840 module (nRF52840).
We have upgraded ncs from 2.6.0 to 3.2.1 and...
I am using a GPIO pin ( P1.05 ) as a reset signal for an external CPU component. The pin functions correctly and stays low when tested in a basic GPIO application. However...
I'm using NCS 3.2.4. When USE_PARTITION_MANAGER is active, the ARM linker script defines ROM_SIZE as PM_SIZE (the full app partition) without subtracting CONFIG_ROM_END_OFFSET...
I have a simple code. send msg to a message queue. and handle the message in another thread. I my old environment ncs2.4.0. I looks works well. // after get msg queue. to...
Dear Nordic Engineer,
Hello!I am planning to develop a 2.4G, BLE and USB mouse. Both the dongle and the mouse device will use the NRF52840. I want to use BLE and ESB simultaneously...
