I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I have tested NPM1300-EK with NRF52840DK and it works.
However, I am using other MCU with NPM1300 but it is a non -zephyr project.
To work with NPM1300, I have tried...
Hi,
I am using nRF7002 DK. I have set P1.04 as UART RX. For testing I am using TI CC26x2R1 Launchpad to send UART data to nRF7002 DK. I use a logic level shifter board to...
Hello,
I am currently trying to connect an external hardware codec and amp (Adafruit MAX98357 I2S Class-D Mono Amp) in order to play audio via BLE Audio and I2S using...
I have an NRF9161DK 1.0.0 , I was trying to do some wiring but the sensors didn't work, then I noticed that the board delivered 1.7v.
I tried changing it to 3.3v using the...
Hi,
My NRF52840DK ( pca10056 1.1.0 2019.9) would not reset when I press its Reset button. The issue is very similar to https://devzone.nordicsemi.com/f/nordic-q-a/38555...
Hi,
What is the minimum LDO dropout voltage of nPM1300? For instance, in order to get 3.3V from the LDO, what is the minimum input for the LDO ? On the datasheet there is...
Dear all:
I have prepare env for border router successfully following this link( developer.nordicsemi.com/.../tools.html , Raspberry Pi4 and nRF52840( RCP: radio coprocessor...
I have a customer that wants to provide me with .a file for some confidential algorithm they want to run. I am tasked with implementing this into my firmware.
Using the...
I can't seem to get the FIFO to work and I think it is because I'm not dereferencing the consumer thread properly. I have reviewed the nRF Connect SDK Intermediate, data passing...
Hi,all
I need to connect BLE via NFC,but I do not know which example should i use to start。and i am a new field of NFC ,is there some document about NFC?thank you a lot...
https://devzone.nordicsemi.com/f/nordic-q-a/44658/communication-probl
I want to change the code provided in this link to enter the password from the peripheral
Hello,
I am using nRF Connect 2.5.2 with a Xiao Seeed BLE Sense nRF52840 and Jlink EDU mini
I am trying to flash the peripheral_hids_keyboard sample with Ozone, and I...
Hi everyone,
I'm trying to measure battery level using nRF52833. Reading previous posts, there are two popular ways to measure battery level with SAADC module 1) battery...
