Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Good day
I intend to use a power saving mode to turn on a device for a set amount of time. During this, the device would still need to receive commands over mqtt. Is this...
Dear SRs
We are evaluating your NB-IoT solution by means of Thingy91 reference board. The NB-IoT service is working with iBASIS card, the question is: can we change the...
I've created the samples for Socket Echo Client https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.0.2/zephyr/samples/net/sockets/echo_client/README.html#sockets-echo...
HI , I am having difficulty in interfacing the flash with my DK board
1) The spi flash sample is getting stuck at flash erase function without any error responses
2) I...
I see this case mentions constant tone extension. Currently, only nRF52833, nRF52820 and nRF52811 can do this.
https://devzone.nordicsemi.com/f/nordic-q-a/59948/nrf52-selection...
Hi,
We're working on a development project using nRF52832, SDK 15.2 and s132_nrf52_6.1.0_softdevice. I'm trying to use the radio test example from the SDK to certify the...
Hi all,
I have a board based on an nRF52832. At the moment I program it through the nRF52 Dev-kit (with the debug out connector) as my board doesn't have any debugger...
I'm a complete idiot when it comes to Nordic, this is literally my first time experience with any Nordic chips. I have a little experience programming ESP32-s3 chips, and...
Im working on a windows 11 Pro (OS Build 22000.1219) with a NRF52 development kit which has a NRF52832 chip set. The board is PCA10040 3.0.0. The device does not communicate...
Hi,
I run the sample zephyr/samples/bluetooth/periodic_adv on 5340, if the controller selected software-base ( CONFIG_BT_LL_SW_SPLIT ), the sample work well; if BT controller...
Hello,
Currently we're working on improving our DALI driver on the nRF52832 chip, because we've experienced issues with transmitting DALI bits with the correct timing. The...
Hello everyone,
I have been trying to get the nRF9160 DK connected to Edge Impulse Platform but it is not possible. i have been following this viedo Connecting nRF9160 DK...
Hello,
I have understood that the pc-ble-driver library is currently in maintenance mode[1] and not getting new features anymore.
We are using pc-ble-driver-py library...
Hello Nordic support,
I am planning to develop an application that will either use Zigbee protocol or BLE protocol. The protocol to be used is determined at startup by reading...
