Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi Nordic team
Last week and before, I tried sdk connect v3.0.0 http_application_update example.
Everything was fine. Pressed button1 to download new bin file and then...
HI DEV
Currently we found a UART Frame error on customer product:
Application scenario diagram
Figure1
nrf52820 ,SDK17.02, softdevice:S132 , gap event length=6*1...
Hi! I'm new to zephyr and nRF boards.
I am trying to write a custom board using the nRF52811. When I try to build examples using the custom board using the command (syntax...
When I asked earlier, it was not possible to send HTTPS payloads greater than 2K due to the TLS secure socket buffer size limit. I see in the most recent modem firmware release...
I'm using nrfjprog version: 10.13.0 / JLinkARM.dll version: 7.50a to flash a firmware onto a custom PCB with nRF52840. Programming hardware is a nRF52840 DK. Our firmware...
Hi,
I am sensing interrupts on a pin using GPIOTE. I can see the interrupts coming on the oscilloscope. The firmware also detects the interrupts. However once I am inside...
Is the IXIT for RF of nrf52832 correct bellow? The test house said the value of inband image frequency should 4Mhz.
IXIT for RF
IXIT Reference
Identifier ...
in \nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\zigbee\experimental\cli\cli_agent_router example , we use the nrf52840 dongle as the Coordinator, for joining the...
what happened when I create a kernel timer (based on the 32k RTC) by nrf connect sdk on nrf 52840 dk?
static const struct k_timer my_timer; static const struct k_work my_work;...
Hi All,
Im pretty new to embedded systems and currently trying to connect a TE MS5837 30B pressure sensor to a nRF52840DK (pca10056) which is all being done via Segger ...
Hello,
I am using openocd to flash nRF52 DK, however, I have several devices connected to my pc at once and I can't figure out how to flash just one of them, When a single...
I need to call the API: clock_control_on( const struct device *dev, clock_control_subsys_t sys)
located at the SDK path ncs\v1.6.1\zephyr\drivers\clock_control.
...
Hi, I am communicating SIM808 with nRF52840. I have made changes in libuarte example and send AT commands to send SMS. I have the following question.
How can I know that...
