Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I am trying to find a solution how to use wifi and ble on thingy91x and manage the coexistence between them, I have found a sample Wi-Fi: Bluetooth LE coexistence...
I am trying to implement the following: I have a mesh node built using the Sensor Server example for publishing temperature data. I want one relay node to transmit the temperature...
Hello All I'm new to the forum so please be gentle! I hope this is ok to ask: I'm in the early stages of planning a project that I hope will be suited to a DECT NR+ platform...
hello!
I'm currently looking for a way to access the nor flash of the nRF7002DK, does anyone have an example of this? My goal is to write, read and erase data to the nor...
Hi,
We are starting our first production run. I have studied earlier assigning IMEIs and how to obtain IMEI numbers via Nordic semiconductor up to 100k devices.
We planned...
Is it possible to get access the virtual com port from an application based on nRF5-SDK-for-Thread-and-Zigbee?
My application requires nothing more than the LED and the...
Hi.
Base On Nrf52840DK , SDK V2.8 and Zephyr
Can't See CTS service when connected to nrf connect (Android App) and source code is "peripheral_cts_client" , Why ?
trying to define a static partition for the NRF5340_CPUNET. even though he can direct the CMAKE to pick up the pm_static yml for each core by adding
does the sysbuild...
Hello,
we are currently testing the capability of updating the firmware of 2 Nordic Development Kits.
The Situation is following:
1 DK simulates a Device which is standalone...
Hi,
I think the following is the link for nrfx flib
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrfxlib/README.html
I know most of the drivers are covered by...
Dear Nordic Team,
After downloading nRF Connect SDK v2.8.0, I didn't make any modifications to the code in the SDK. I directly compiled and flashed the locator_tag example...
Hi,
I have a scenario where I need to capture the power consumption of a specific period for individual power lines. I understand that I need to use the ammeter feature...
HI ALL,
I used a system off demo and added the following content.
The power consumption tested was around 1uA, which should be normal according to the errata. Then...
Hi, I am having issues with one of our wifi scanning modules not detecting the wifi beacon using the 1M rate . Looking into the PHY level, I demodulated different wifi beacons...
