Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi... I am using 15.2 version sdk , i have merged ble_app_uart and twi_sensor example code . complied successfully but while running after two output data i am getting fatal...
Hi,
I successfully added libuarte async library to the ble_app_uart example. Now I am able to receive data over UART from another board and my goal is to transfer it to...
While still trying to debug the disconnect problem in a different thread (unsuccessfully), I've gone to the ATT_MTU_THOUGHPUT example, to try and understand it and gain more...
Hi,
I am working with a custom board with a third party NRF52832 module. On my board I have a DS3231M real time clock IC communicating with the NRF52832 via I2C/TWI and...
I am trying to have a bluetooth bond between the device and the app,
how to set a security key to bond it with the android app? and also can I know how to encrypt all the...
Hi,
I have a question about getting the appkey from flash:
I am using the device state manager for key management. I do a ramdom generation of netkey and appkey on first...
I have a few different Fanstel Eval boards that contain the nRF52840 SoC - starting with the BT840XE. I'm able to flash the board with example firmware and my own custom firmware...
Been working on an unsoldered, untinkered, and in all ways untainted nRF5340-PDK. No jumpers changes. No solderbridges cut. All working fine, but all of the sudden I cannot...
Hi! I want to program a custom BLE application (as Central/master/GATT client device) to run on a Windows PC using a nRF51 Dongle (PCA10031 board) attached through USB in...
Hi,
I am working on the software development of a product based on an nRF52832.
We began our development on the nrf52810 and then moved on to the nRF52832 as it became...
Hello,
I'm struggling to connect to an MQTT-SN Gateway when the device is configured for low power. Currently using MAC-OS Catalina 10.15.3, SES version 4.42 and have tried...
I tried to install the nRF Connect SDK v1.3.0-rc1 error
I open git-bash.exe to execute the ncsmgr init-ncs command, the following error occurred during the installation...
nRF Connect SDK v1.3.0 using nRF Connect v3.4.2 - ToolChain Manager
I am trying to install nRF Connect SDK v1.3.0 using nRF Connect v3.4.2 - ToolChain Manager using nRF...
I am writing a code to blink the LEDS , the 3rd one is not turning off.
Here is the code-
#include <stdbool.h> #include <stdint.h> #include "nrf_delay.h" #include "boards...
