Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I'm currently developing a firmware running on nRF51-dongles (PCA10028). The dongle communicates with a PC application over UART. Everything is working fine except...
Hello we would like to use the Nordic chip to send wireless messages from a node to other nodes directly,without hubs. We wouldn't like to be limited to up to 8 nodes receiving...
Hello,
Setup: Android 4.4.2 (LG G2), nRF51822 peripherial.
I noticed that once in a while when trying to connect to my nRF51 based device it won't connect and what is...
softdevice 8.01,app is hts. ceilphone is HTC one. nrf tools.
add some functions display，adc, eg. use nrf tools HTM connect to the board, it's reboot every time when clip...
I'm using nrf51422, SoftDevice 310 and SDK 6.1.0, when i call sd_ppi_channel_enable_set, it causes SOFTDEVICE_NOT_ENABLED error, but softdevice was enabled earlier with SOFTDEVICE_HANDLER_INIT...
Dear all.
I have some test result on DFU feature. Please any comment on this issue.
test condition
Mater control panel (64-bit version)
nRFgo studio...
In my application, I had these lines.
nrf_gpiote_event_config(0, mPinDat, NRF_GPIOTE_POLARITY_LOTOHI);
nrf_gpiote_event_config(1, mPinDat, NRF_GPIOTE_POLARITY_HITOLO...
Hi,
On iOS, is there any way to download files right into the nRF Toolbox "User files" ?
This would be useful for DFU tests, to retrieve my binaries from the web.
For...
Hi everyone,
When I set the radio's transmit power, I can use "sd_ble_gap_tx_power_set" function. If I want to get the radio's transmit power, is there any function I can...
I am using NRF_GPIOTE->EVENTS_IN[0] and NRF_GPIOTE->EVENTS_IN[1] in my software. I had my own GPIOTE_IRQHandler working.
Today I am adding UART module into my source code...
Looking for a 3rd party Nordic based BLE module that comes with a chip antenna and exposed pin headers so I can quickly solder a AA battery housing and a single SPI board...
I'm using nRF51822 Beacon v1.1.0.
It seems interrupt has ocurred every 256msec.
I want to change timing of interrupt interval.(like a 512msec, 1024msec etc.)
Is it possible...
We're making a height sensor with Bluetooth connectivity using a simple HC-SR04 ultrasonic module, which outputs the height as a pulse with certain width. The width of the...
