Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello,
I am relatively new to the nRF Connect SDK and I'm developing an application for nRF9160DK on toolchain version 2.0.2.
I am working on a non-secure application...
Hi, I am trying intialize the RTC in ncs using nrfx drivers and then connect it tick event to a saadc sampling event using a ppi channel. I learnt that RTC0 and RTC1 are used...
Hi
after create project from sample broadcast_audio_sink, when running it, i get following message:
[21:59:46:406] *** Booting Zephyr OS build v3.0.99-ncs1-2483-g482dcc7865f7...
I need to modify the code of different sensor data, which is obtained on LTE monitor, so I want that file in which I can create custom sensor data /Modify the sensor data...
Hello.
I had LC3 access granted.
I can access nrfconnect/sdk-lc3 on my web browser.
However, with bash, I get the following error and cannot build nRF5340_audio.
...
Hi Mate,
I have very small issue that is when i am trying to link config_bootloader_mcuboot=y in zephyr application the program is not flashed. I need to run zephyr application...
I was curious if there was a delta firmware update file to go from 1.3.1 to 1.3.0 on the nRF9160. Most of our business is in North America and we use a carrier who requires...
Hi all,
I'm trying to use the nrf Connect SDK and configure PWM to use in one pin from nordif nrf52DK. The final chip will be the nrf52810. I have configured the builder...
Hello,
I want to use pc-ble-driver WITH an EV-BT8400XE.
I develop with SDK15.3 (last compatible version of SDK for pc-ble-driver)
I am successfully able to use pc-ble...
Hey all together,
I'm using nrf Connect SDK 2.0.0 and want to place a variable in flash at a predefined location. The reason is, that I need to read the information stored...
Hi,
I'm setting up nRF Connect SDK according to this instruction ( http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing.html) and Getting Started...
Hey,
in our project the nrf is acting as the central and connecting phones.
As part of the connection process:
1) We check if the phone is bonded in the nrf.
2) We...
Hi,
I'm on NCS 1.8.0 and I've successfully built and run the peripheral_nfc_example sample. Printed logs when reading NDEF message using a smartphone
When I came to...
I have a nRF52840-DK that stopped programing.
As a starting point to get it back to work, I reflashed the Interface MCU Firmware.
It is correctly detected by J-Link Configurator...
Hey Nordic,
My project is based on "ble_app_uart" and "ble_app_uart_c" examples. I modified them to some extent. You can download them from here .
Normally, I can write...
