I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello,
I received an email regarding the new course for nRF54 series parts and when I click on the link I am blocked by a Cloudfare generated web page. The Cloudfare ray...
Hi, We currently have a custom board with a nRF54L15 (final production silicon) paired up with a nRF21540 RF front-end module (FEM). This board is running Zephyr with v2.9...
Hello! I am using the nRF7002 in promiscuous mode to capture Wi-Fi traffic. Everything went smooth in AP mode where we use another nRF7002DK as a transmitter and our computer...
Hello,
We are entering preproduction build for a custom design using the nRF54L15. We need to know the solder ball dimensions and the recommended solder-mask dimensions...
Problem:
Reset reason logic works correctly when programming via SWD
After DFU programming, reset reasons are detected incorrectly
Even after unplugging/reconnecting...
Hello all, I've just bought nRF9151 DK and went with Quick Start. I loaded nRF Cloud multi-service sample. Sample runs and connect to network. Sometimes it sends data (location...
I am following the Cellular IoT Fundamentals course and trying to get my nRF9151-DK set up as a device in the nRF cloud. ( https://academy.nordicsemi.com/courses/cellular...
Hi
I have two nRF54L15 DK boards (PCA10156).
Both are behaving the same way right now.
.......................................
ONE: Using nRFConnect in VSCode...
Hi,
I am currently developing a heart rate strap using SDK 17.1.0 and the S312 SoftDevice with the nRF52805. I have noticed an issue: when I connect the heart rate strap...
Hi
I'm using the periodic_adv_conn example from SDK 3.0.0. In the request_cb function, the bt_le_per_adv_set_subevent_data function is used to load data for future subevents...
Hi,
I want to use the die temperature sensor in the nRF54L chipset and am wondering why the definition have changed slightly compared to previous chipsets. In the SoC device...
How precise do the trace antenna dimensions have to be? Given that the datasheet for the nRF54L15 only has a reference layout up to and including the matching network, but...
Hi Nordic:
We currently need to provide the RoHS and MSDS test certificates for our product's NRF52820QDAA-R. I checked the certificates on Nordic's official website, but...
While testing, I encountered the following error after flashing the modem firmware and running the DECT example:
<err> nrf_modem: Modem has crashed, reason 0xfff, PC: 0x0...
Greetings,
I want to change Device name on Advertising. Is that possible? I am using nrfSDk52832, I want when some state of Switch is change, to change advertising name...
