Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
I'm currently trying to figure out how exactly the workflow for updating forked repository (i.e. sdk-zephyr) should look like ideally. https://developer.nordicsemi.com/nRF_Connect_SDK...
I'm experiencing a strange issue that I can't seem to figure out. We've built a location system based around the nrf52833, and we're currently running this system in a pilot...
Hello,
My name is Edward, I am trying to configure a net Thread with auto selection channel, do you have any example about this?
I have based my development on the simple_coap_server...
In the SDK ble_gatt_db.h file the ble_gatt_db_srv_t struct has a member misspelled as "charateristics" rather than characteristics. Was that done on purpose?
Hi,
I would like to resume the discussion made a few days ago in this post.
Is it possible to hide some BLE services until the connection is successful? I want only my...
I'm just starting... I have a little programing experience and knowledge of electronics
My project is controlling stepper motors over ZigBee using cell phone.
I have Samsung...
I have an application where I need to periodically write a few KB of data from my nRF to a host computer. Since TXD.MAXCNT tops out at 255 bytes, I'm trying to set up all...
Hi. I am trying to add a RTC to my ble project. I copied all the simple code from the RTC example, and set all the sdk_config.h settings to match.
As per usual millions...
Looking to permanently change UICR REGOUT0 to 5 for 3V3 on VDDOUT from dongle, to power a small Pulse Oximeter. Then using nRF Connect SDK and Zephyr, get Bluetooth GATT services...
Hi,
As a newbee :-)
Im trying on an nRf5340DK board. I use NRF-connect/Vusial Studio Code: I managed to use zephyr/samples/basic/bkinky example with a build in nrf3540dk_nrf5340_cpuapp...
I erased a board using a MAC (Monterey 12.1) and a Segger Version 11.0 Part-no 8.19.28
nrfjprog --masserase
After which I was no longer able to program, connect, or recover...
Hi,
I was wondering if it was possible to avoid JWT for the NRF9160 by establishing connection between an MQTT Bridge to Google Cloud. Our goal is to establish 24/7 connection...
Hi NRF folk,
when I build sample projects in VSCode (ncs1.8) it works only for some projects (zephyr_st_ble, zephyr_system_off,...). When I use any of the sensor project...
I am using nrf52840-DK and trying to get the Zigbee Switch working. This is just a plain zigbee switch with no bind to light. However, this set attribute during init results...
