If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello I am investigating the power consumption of the nRF9151-DK using PPK II. The measurement settings are as follows.
・Connect PPK II's VOUT and DK's P22 VDD_nRF. ・Connect...
I use nrf5340 audio DK, SDK v3.0.2, and added an iso.conf,
A lot of warnings were reported during compilation.
Are these conf not effective?
If I want these conf...
I'm interested in configuring a NR5340DK as an end device on a Zigbee network where the coordinator is a 3rd party device that uses legacy Zigbee. I'm fairly new to Zigbee...
Hello. I'm trying to call an interrupt service routine (ISR) using IRQ_DIRECT_CONNECT, but it is not working.
Here is the flow of my code:
So, it is expected to print...
Hello,
I am adding security feature for BLE in nrf52810 custom board. I am using v2.9.1 toolchain and 2.9.1 sdk files
PFA BLE related file as well as .conf file as well...
What is the quiescent current of the PM1300 when it is not in SHIP or hibernate mode, but when it is "alive" and configured and running off the VBAT terminal, ignoring any...
Hello, I’m working with a custom board using nRF7002 + nRF5340 + MX25R64 (SPI4) , and I’m trying to perform firmware updates over Wi-Fi using a firmware file hosted on an...
Good evening. We're running into an issue with using all 4 peripherals on the nRF9151. At the moment we are using the 9151DK.
The issue arises as soon as we enable spi1...
Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
When I use DTM mode and config nRF54L15 to 8dBm, I only see 5.3dBm. And I tried 3 boards, they are the same. Is that normal or not
The whole cable loss is lower than 1dB...
I just received a Thingy 91X, and am having problems out-of-the-box. I used the "Quick Start" module of the SDK. I selected the option that programs the hello.nrf.cloud connectivity...
I've been trying to flash an nRF52840-DK with code that successfully builds on Segger. The Segger error is "Failed to connect to target." I updated the devkit firmware with...
I have been using visual studio code on mac for development, and it started showing error code 63 when I try to start debugging on the 9160 based hardware. It used to work...
Hello,
I am studying the materials in Bluetooth Low Energy Fundamentals.
I cloned the codes from GitHub https://github.com/NordicDeveloperAcademy/bt-fund
I tried to...
