Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
We are encountering an issue with flashing firmware to our newly designed nRF54L05 BLE board.
Issue Details:
We are trying to flash a .hex file (simple Blinky code...
Dear Nordic Support,
I am currently performing initial tests for distance measurement using Channel Sounding with the nRF54L15 Development Kit.
Here are the details of...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi Nordic team,
We are interested in using nrf9161 SiP. can you confirm if the `zephyr,nrf91-slm` driver work on the nrf9161? We are interested in the DECT NR+ capability...
Hi i am trying to configure a timer to work in count mode and when it hits a certain number ( for example 100) to activeta an interrupt, clear count and start again.
Best...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Hello!
I am trying to set up automated tests for an application on the nRF54L15 BabbleSim target. The application needs two-way communication with a test script; this would...
hello
In the nrf/sample/net/aws_iot example, when updating a shadow topic, use $aws/things/<thing-name>/shadow/update/
Where does "thing-name" refer to?
Regards,
Dae...
Hi All,
We have an application that was compiled on nrf54L15DK where we get UART logs . The application was tested on DK and is working fine. Use Case:
Wanted to run...
I am interfacing the DS18B20 digital temperature sensor with the nRF52810 using the nRF5 SDK . The same firmware and hardware configuration works correctly on the nRF52832...
Hi,
We are facing a critical power consumption issue in our nRF52-based Zephyr application , where some devices randomly enter a high-power consumption state (~80+ µA) instead...
Hello,
I am currently using the bt and uart backend for zephyr logging on ncs 2.9.2. I want to be able to save logs to flash which will be useful in debugging/ and be...
I am trying to establish a BLE connection between two nRF52840 devices.
The child devices are properly advertising and are close to each other.
When attempting a BLE connection...
Hi,
We are running into a serious issue with OTA. Specifically, we have observed that nRF52832 will not be able to perform OTA to a newer firmware given that it is previously...
