Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hey all - I'm new and trying to connect Thingy91 to nRF Connect V3.6.1 for the first time. When I open the Programmer app I only see "No devices available" in the drop down...
Hi,
I'm trying to follow the NCS tutorial in: https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts/nrf-connect-sdk-tutorial---part-1-ncs...
Hi,
we are developing a custom BLE communication. For this we are using:
- nRF5_SDK_17.0.2_d674dde - s332 - based on BLE NUS UART example
Everything works fine, until...
I'm trying to open a NCS project in SES but I'm getting error 1 from create_nordic_project.py. NCS 1.5.0 installed with toolchain manager on macOS 11.2.2
The error in SES...
Hi,
I am following a client case that they have issue on accessing SD card via SPI port.
I used the sample project fat_fs on nrf9160_pca10090 DK and used SPI_3 to access...
nRF9160 DK schematic sheet 2 missing pin names for WP and HOLD of nRF91_EXT_MEM in the On-board interface (far right page 2)
could someone post what nRF9160 pins are used...
Hi,
I have written one application with logging disabled to save power.
However, when I tried to debug the code with Ozone, during startup, it raises BusFault exception...
Hi,
I am currently working on generating a dfu over serial uart by testing with the ble_app_blinky example given in the SDK 15.2.0. Currently the ble_app_blinky hex file...
Hi ! Using nRF52840 whith SD140 as central and 6 link count I research :
changing the NRF_SDH_BLE_GAP_EVENT_LENGTH from 6 to 2 does not change "Window size" on CONNECT_REQ...
Hi,
I messed up my SES project and now the debugging session doesn´t start and the debugger does some weird stuff and doesn´t execute my application.
I also tested if...
Hi,
I am using the DFU example given in the SDK15.2.0 to try and update the application on my NRF52840. Currently, I have been able to update the application to run the...
I use many SEGGER_RTT_WriteString and SEGGER_RTT_printf sprinkled throughout my code which was very helpful for debugging and monitoring, however, we're getting close to releasing...
I have attempted to update the firmware on the Nordic Thingy:91 via usb connection to my laptop running CentOS 8, however, finding great difficulty updating the firmware through...
My stm32 (as a master) uses SPI to communicate with nrf52840 (as a slave) When my nrf52840 wants to send data to stm32, it will pull a GPIO to let stm32 generate a GPIO interrupt...
I am using a BL632 DK from Laird, trying to erase the onboard 52832 device. I can connect to the target, but it fails when try erase all.
Results from connect target:
...
