I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi, i would like to work with nrf52832 for my IoT idea. So my question is where do i start from to work with this particular SOC nrf52832 chip? My End product would have integrated...
Dear Madam/Sir,
I'm trying to compile the ble_proximity example on SEGGER Embedded Studio with SDK 12.3.0 and SoftDevice 2.0.1 to run on nRF51822 with PCA10001.
After...
Hey,
I have implemented the ble_hid_mouse example in the nRF52832, and implemented both central multilink and USBD in the nRF52840 dongle so that both boards are paired...
Hi,
We are using nRF52840 in our product for both Client and Server communication on BLE5. We are seeing an overall average time of 5+ seconds for the overall connect, data...
Hello everyone!
I have started to work with openthread recently, and now I have to build a mqttsn client into a stm32 uController. I'm doing that by using the spinel protocol...
Does the nrf52832 has some delay when the shortcut of END_START is enabeled in continuous receiving?What is the meaning of rx chain delay?Does RX chain delay in 2Msps mode...
I'm having problems getting the peer manager to work in a project forked from the ble_app_template on my nRF52-DK (using pca10040e, S112), complaining it can't initialize...
Hi, I am using ble_app_uart_saadc_timer_driven example, which work just fine when receiving data on smartphone (using nRF Connect app). Now I would also like to do the same...
Hi,
I'm using the Nrf52810 with softdevice S112 for the moment.
Question 1:
In ble_gap.h i see that there is a define BLE_GAP_WHITELIST_ADDR_MAX_COUNT (8). Is this realy...
Hi,
I am reading a voltage value from an analog sensor which changes values with 0.02V step. So, i need the accuracy up to 0.02V from ADC channels . But right now i am...
Hi,
I have project based on nRF52840 (using SDK 15.2) and I have a problem with properly adding ADC measurement using scheduler - description as below.
Problem description...
Hi
I want to create this example:
A major network,it include the subnet A and subnet B.
One node X,it belong to subnet A and subnet B.
If the node X was a function...
Hi
We currently working on nrf52 dk with SDK15.0.0 but we will use nrf52810 rather than nrf52832 due to cost.
As I know, nrf52810 doesn't have FPU compared to nrf52832...
