I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
Yesterday I installed the image ' RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha.img' on a Raspi 3B+ and cpnnected a Nrf52840 DK via native USB. Using the 2.0.0 Thread...
Environment:
Nordic SDK 15.2.0
Eval kit nRF52840-DK / PCA10056
SES debugger on Windows 10
I was trying to integrate nfc_callback() for ...EVENT_FIELD_ON / OFF from...
Hello,
I have a problem with MQTT Publisher example on my nrf52832 DK.
1. I am using ubuntu & nordic's SDK15.2.0 for this mqtt example. On raspberry pi 3b I have installed...
I need to communicate with a sensor through SPI. However, in order for the sensor to switch to SPI mode, its CS pin must go down. So before I do SPI transfer, I clear that...
Hi,
I want to interface RGB LED- APHF1608LSEEQBDZGKC (Kingbright make) with nRF52840 operating at low power mode on 1.8V (@Vdd). The 1.8V external source is capable to drive...
Hi Nordic,
we use the demo "ble_app_hrs_freertos" (nRF52832, SDK13.0)
I'm trying to get it into low power (system on mode) , and the idle task keep on running and the...
Hello,
I had to hard code new MQTT broker settings. Specifically the NRF_CLOUD_HOSTNAME. Whenever I update the nerf_cloud Kconfig to select a new broker, the autoconf...
Hi
On our project we see often softdevice asserts with the version 6.1.1 of the S132. The application we have is offering a BLE GATT service that allows fast serial communication...
We are starting different projects around the Thingy :52. When studying the SDK and harware doc we are faced with a possibly stupid question : we have identyfied an accelerometer...
Hello all. I have been having issues using the hash functionality of the nrf crypto library.
Above is the screenshot of the output I am getting for the code shown below...
I am struggling with the Zigbee SDK for the nRF52840. I have successfully run the light switch demo with the PCA10056 board as the switch and two dongles behaving as coordinator...
I have been struggling to get a Zigbee end device talking to a SmartThings hub which is on channel 14. I have now discovered that regardless of the channel mask I give it...
I followed instructions given here https://devzone.nordicsemi.com/b/blog/posts/segger-embedded-studio-a-cross-platform-ide
I got it working in Build and Debug mode. However...
