Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a few questions about how exactly the free flash space is intended to be managed with a banked DFU transfer. We observed some devices encounter problems after a DFU...
I am incorporating the MESH 5.0.0 coexistence example over an existing BLE application. I have run into an issue that I have been unable to resolve involving Persistent Storage...
HI,
Am using west tool to build and flash .and am following this link. https://docs.zephyrproject.org/3.0.0/guides/west/sign.html . they mentioned in that link after the...
Recently, I've been trying to send the data acquired by sensors like thermistor and microphone to the mobile phone or PC through BLE from the nrf52840DK. I want to develop...
Hi there:
I were develop product with nrf52832 ,nRF5 SDK version 17.0.2 and mesh sdk 5.0.0. And i install the toolchain on the ubuntu 20 follow the guidance https://infocenter...
Hi Nordic,
I am working with nRF52840, sdk17.1.0 and got a pcb with external flash with GD25Q16E.
Pins usage are: SCLK: P0.25, CS:P1.00, SIO0:P0.21, SIO1:P0.15, SIO2:P0...
Hello everyone,
I am developing a product with nRF52840. The board has a magnetic sensor (LIS3MDL), a ToF sensor and a LoRa module (Sx126x).
I have worked with nRF52 products...
Hello all!
I would like to use the PWM driver, yes, the hardware that is on board the chip. To get going certain code parts from the PWM driver that comes with the SDK,...
Hi there,
We are using the Serial LTE Modem MQTT client .
So when the #XMQTTEVT messages comes in, the first parameter <evt_type>, is documented well here:
However...
Hello.
I want to write 3 bytes of data using BLE in a memory area that will not disappear when the nRF52820 is powered off or reset.
Currently, when I create a program...
Hi, I trying to run the spi_flash example form zephyr.
My sdk in 1.9.1 - nrf52840 in a custom board.
I have tried everything and I always get the same result:
JEDEC...
Hello,
Aim : To write and read x bytes from the QSPI interfaced external PSRAM(APS6404L-3SQR) using the nRf52840.
Configuration : Following is the configuration of the...
Dear support
I am developing a generic central application intended to connect any BLE devices which is connectable. So I need to figure out which parameters are needed...
hello Nordic
i am working with nrf52832, ncs 1.7.1
we have to turn on the power before trying to read jedec and to avooide changing ncs spi_nor or using SYS_INIT we decided...
Dear Nordic-Support Team,
Introduction
I have read through some sources (tickets and documentation) but I am still struggling to see the big picture of UART configuration...
