Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hello,
I am trying to get an MQTT TLS connection to AWS up and running on my thingie91 (nrf9160). I am using SDK 1.5.0 and the sample "aws_iot".
Even though there is a...
Hello,
what is the CPU speed of nRF52832?
I'd like to test if the NRF52832 is running at 32MHz or 64MHz.
I used it to run a compression algorithm, which took 8ms to...
I have seen this question asked a few times--but every thread seems to have no concrete answer.
I have uninstalled and reinstalled all JLINK drivers.
But still get the...
I am using the nRF9160 for IOT with the console connected on UART 0 there is a string of +CSCON: 1 and +CSCON: 0 messages displayed.
Build Zephyr 1.5.1
Modem firmware...
We're looking for some clear documentation for implementing OTA DFU via BLE on the iOS side. We have the firmware working well on our dev kits here, but working only with...
Hi,
Can you explain please why do you use all flash space for application (except SD area) in your examples. For example, SDK 17.0.0, HRS s132 example starts from 0x26000...
Hi
I have nRF SDK 17.0.2, and looking for ble_app_template application for PCA10100 to be flashed into nRF52833 DK. But seems that is not available.
Is there any other...
I'm developing a C implementation for nrfutil to make a Serial DFU in bootloader of sdk11. But I'm having an issue in serial communication. I've used a serial sniffer to compare...
I am using nRF52840 DK and connecting it with SPI to ESP32. The first bit of the transmission is missed for some reason. I could verify that the transmission is ok with logic...
Hi Nordic,
I'm working on a project using SDK 15.3, s140 , based on the LESC example for a central and peripheral application. I am able to bond with devices and later on...
Hi,
The MMD example published by the Nordic Team ( https://github.com/NordicPlayground/j-link-monitoring-mode-debugging ) is supposed to work with the nRF52DK (PCA10040...
Hi,
We have a custom board with nRF52840 based ISP1807 and developed the fw to some point. For some reason we tried to run the same fw on the nRF52840 DK rather our custom...
I'm trying to program an nRF52810 on a custom PCB using the nRF52-DK and am getting this error ((0x4) Lowlevel error: Unknown value (ffffff24)) when connecting with nRF Connect...
Hi there,
I'm working on something with hard real-time requirements - for this and a number of other reasons, I'm writing directly to the registers.
I'm trying to generate...
