Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hi, I'm looking for clarification whether the DECT NR+ modem firmware supports GNSS. Legacy docs say it doesn't, but there is no mention of it in current docs. Based on that...
In my application with nRF5340 and nrf connect sdk 2.3.0 which works well as Peripheral, if I activate CONFIG_DM_MODULE=y I always get the error "...ld.exe: region `RAM' overflowed...
I had an opportunity, to do a complete pristine reinstall of Windows 10, and to then do a pristine install of Visual Code, nrf connect, etc.
After doing that I did this...
Hi,
I am working on a project where we need to connect to multiple peripherals which also include mobile devices. (up-to 10) on BLE central.
We need to measure the distance...
HI,
I find that the vs code always loading something as below, the Kconfig has some empty.conf, and can't create new Projects.
Then I return it to V2024.9.87, It works...
Hello, guys
We want to evaluate nRF9151 SiP the following way:
To set it to operate in serial mode in which it is ready to receive AT commands (it comes pre-flashed...
Hi,
I've been developing a Matter device based on the nRF5340 SoC, and have been using the DK up until now. We've been developing a custom board in parallel. I've created...
I have nRF Connect SDK v2.6.1 installed on a Mac, the latest toolchain installed via nRF Connect for Desktop, and VSCode with all the nRF extensions. Everything works pretty...
Hello,
I have a custom hardware, with an external 128MB QSPI flash memory connected to a nRF5340. My current task at hand, is to store firmware update images for MCUBoot...
If I am having a custom board created and assembled using a pcb maker (makerpcb, jlcpcb, or pcbway) what do I need to ensure is on the board so I can flash and debug it? I...
We have a issue about nRF9161 on our custom board.
we flash hex our board. It doesn't work very well. sometimess it work and consume about 90mA current. sometimes board...
I have the following setup in my overlay file:
relay { compatible = "gpio-relay"; relay1: relay_1 { gpios = <&gpio0 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; label = "DC Mtr...
In our project we use a SHT4x sensor connected to I2C bus of nRF5340. To lower power consumption during idle/sleep we've a power line switch to disconnect the SHT4x from the...
Hi Nordic team,
I was testing whether Zephyr's LLEXT would work on the nRF52840DK. The example can be compiled on NCS 2.7.0 and loads fine. However the final step of having...
