I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
I have a question: Is it possible to use BLE Long Range mode (Coded PHY) in the NRF52840 with mobile phones? If not, is there a solution to use it in parallel with normal...
I am using NRF52840's NFC with apple wallet but it requires certification from Apple to be used as tag reader. How can I get it certified so that I can read data from apple...
Hello,
I need to be able to send/receive binary data over this BLE UART Service (bt_nus) on macOS. I'm using the peripheral_uart sample project with no success. It seems...
https://github.com/zephyrproject-rtos/zephyr/blob/main/samples/drivers/spi_flash/src/main.c#L36 may I know where I can find the pin connections used in this example
"const...
Hello all,
We're on the initial stages of a design that requires Wifi (ideally) in a very challenging environment, where in the worst case scenario the temperature could...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
I have a BME688 connected to a NRF52840DK and I cannot get a working I2C communication using Zephyr. Below are all sources:
app.overlay
main.c
prj.conf
I was...
Hi.
I am trying to disable the RESET pin (P0.21) on the nRF52810 microcontroller (custom board) and set it up as a normal I/O pin.
I'm using the SDK v2.6.0.
I don't...
Hi, my device is central device( Central UART ) and I couldn't get stable pairing with peripheral device with display which provides passkey code. The scenario: 1. From the...
Following instruction here for setting up NRF52840-Dongle as a radio coprocessor for use with OpenThread Border Router.
The error is at the second step when executing "...
I'm alter the overlay file to adapt my board.
In my board,I try to use pin 9,10 as uart_tx and uart_rx,without cts and rts.
I wirte it in my app.overlay as follow:
...
I am currently working on a project where I need to connect my nRF52833 microcontroller to other devices using the Nordic UART Service (NUS). I am using the nRF SDK and Segger...
Hi,
I created a custom board following the instructions from https://www.youtube.com/watch?v=V_dVKgWKILM . Everything is ok and with the "Hello world" example builds without...
Hi,
We have our custom PCB with an nRF9160 SIP that is connected to a nRF9161-DK via P20. I have a couple questions about this setup.
Is it fine for us to program...
