Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I have sdk 2.1.0 and nrf5340, trying to run peripheral_uart sample connecting nrf5340 to a module via uart. The program seems working when only works with nrf5340 based on...
Dear Nordic Support Team,
I wanted to configure the nRF52840 dongle as radio co-processor. For that I wanted to build and flash the Thread: Co-processor sample in nRF52840...
Good day
I intend to use a power saving mode to turn on a device for a set amount of time. During this, the device would still need to receive commands over mqtt. Is this...
Dear SRs
We are evaluating your NB-IoT solution by means of Thingy91 reference board. The NB-IoT service is working with iBASIS card, the question is: can we change the...
I've created the samples for Socket Echo Client https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.0.2/zephyr/samples/net/sockets/echo_client/README.html#sockets-echo...
HI , I am having difficulty in interfacing the flash with my DK board
1) The spi flash sample is getting stuck at flash erase function without any error responses
2) I...
I see this case mentions constant tone extension. Currently, only nRF52833, nRF52820 and nRF52811 can do this.
https://devzone.nordicsemi.com/f/nordic-q-a/59948/nrf52-selection...
Hi,
We're working on a development project using nRF52832, SDK 15.2 and s132_nrf52_6.1.0_softdevice. I'm trying to use the radio test example from the SDK to certify the...
Hi all,
I have a board based on an nRF52832. At the moment I program it through the nRF52 Dev-kit (with the debug out connector) as my board doesn't have any debugger...
I'm a complete idiot when it comes to Nordic, this is literally my first time experience with any Nordic chips. I have a little experience programming ESP32-s3 chips, and...
Im working on a windows 11 Pro (OS Build 22000.1219) with a NRF52 development kit which has a NRF52832 chip set. The board is PCA10040 3.0.0. The device does not communicate...
Hi,
I run the sample zephyr/samples/bluetooth/periodic_adv on 5340, if the controller selected software-base ( CONFIG_BT_LL_SW_SPLIT ), the sample work well; if BT controller...
Hello,
Currently we're working on improving our DALI driver on the nRF52832 chip, because we've experienced issues with transmitting DALI bits with the correct timing. The...
Hello everyone,
I have been trying to get the nRF9160 DK connected to Edge Impulse Platform but it is not possible. i have been following this viedo Connecting nRF9160 DK...
