I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi,
I tried building and debugging the sample "https_client" using the method described here . But debugging fails. Debugging stops prematurely because the source file cannot...
I need to be accurate to five decimal places.
Use nrf52840 and ses.
Test code:
Execute d=atof(mm)/60.0 result 0.70693.It's right.
But e xecute d = 0.70693+22 result...
I am trying to use SAADC.
When viewing the contents of nrfx_saadc.c in SEGGER IDE all the code is greyed-out.
I verified it is enabled in sdk_config.h:
// <e> NRFX_SAADC_ENABLED...
Hi everyone,
I am currently attending the nRF Connect Fundamental Course.
As you can see from the picture below (taken from the Course material), there must be the chance...
Hello DevZone,
I was tinkering around with the speed of the TWIM0 module in the nRF52832.
I have a cheap USB logic analyzer to help me display the waveforms and I made...
Hi,
I am using NRF52832 development board , to which i have interfaced LIS3DSH accelerometer sensor(3.3V i2c)
when i configure it for 1600 sampling rate and all the...
Hello,
I am using nRF Connect for Desktop v3.12.0 with Programmer v3.0.4 on Mac. When I program mfw_nrf9160_1.3.2.zip on the nRF9160 dev kit, it works, but when I try on...
Hello! Very quick question. The available Zigbee and ZBOSS NRF documentation repeatedly to code examples that I am unable to find. The only examples I have are at nrf/samples...
I've previously successfully done interval advertisements using a SoftDevice with Nordic's previous (non-Zephyr) sdk, but I'm having issues replicating it on Zephyr.
Our...
Hi, I am using the nRF52840 with the softdevice s140 6.1.1 with the SDK 15.3 with FreeRTOS. Sometimes after collecting data for a around a day the device sometimes crashes...
Hi,
It has been a while since I looked up on different resources to get SPI slave transaction example and I finally found on the `nrf / samples / tfm / tfm_secure_peripheral...
Hello,
I have three questions regarding FEM.
#1 According to the following URL, FEM function is supported only for nRF52 series.
Would the FEM function be available...
Hi We are working on a new product that includes NFC, When we measure the voltage level we do not reach more than 600mv. The matching was done by capacitors: using a 2uH antenna...
Dear all,
I could happily flash my firmware to my nrf52840 upon pressing reset button. When pressing the reset button the diode on the board started to beat red and via...
