before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
I have a NRF52840. To save some energy I wanted to disable the soft device so that there's no bluetooth activity at all. However instead of an average consumption of about...
I am developing BLE Mesh product with `nRF connect SDK`.
I understand most of sample project has a function of proxy node. But I don't know how to connect a provisioned...
I've upgraded several Thingy91 boards successfully with the latest firmware and have ran into an issue with another Thingy91 that I've purchased. Here is the error when I...
Hi,
I am storing sensor data into flash and sending it to client when it is requested by Indication characteristic.
I don't have any issue with reading/writing/updating...
Hello developer,
I am new here and learning Beacons with the Board nRF52840 Feather from Adafruit as scanner and Segger Embedded Studio. I refer to nRF52 SDK 17.0.2 and...
Hi all,
I have connected my PPK II to my pc (Ubuntu), installed the software and connected the device.
I can't seem to find the mode or start button anywhere on the user...
Hello everyone,
I am using the fanstel BC840, where the tx and rx pins of the uart are alloced on 1.02 and 1.01:
So i have created a custom_board named hello_board...
Hi,
I’m trying to test/confirm the accuracy of the 32kHz crystal oscillator and the 32MHz crystal oscillator by toggling a GPIO at a derived rate and at 50% duty. But I...
The tag options did not include just nRF Connect as an option so I picked something that had nRF Connect in it. This issue has nothing to do with the SDK.
This is a question...
Help me simple LED Blinkink nrf51822 AA type i'm using YJ-14015 and stlink compiler.. i'm also using keil for IDE. i don't know how to create program and setting for compiler...
Hi,
Using nrfutil tool to transfer firmware package on Windows 10 system is much slower than on NRF toolbox on Android phone. How can we improve the transfer rate of nrfutil...
Hello, when trying to program a custom board with an NRF52805 with a J-Link from SEGGER Studio using one of the examples for the board "nrf52dk_nrf52805", I get an error saying...
Dear Devzone,
At the moment, We do not have methods to measure the GPS sensitivity of our products based on nRF9160.
We are using an active antenna with LNA gain 16dB...
We are using the NRF52 as a SoC in a sensitive analog application,
I need to model power supply noise created by the DCDC convertors REG0 and REG1.
Is there a SPICE model...
Hi Nordic team,
My dev environment is as follows:
nrf52840 + s140 +SD6.0.0 + SDK15.0.0 + SES + nrf52840-DK
Here, nrf52840-DK is configured as BLE Central and my peripheral...
