I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
We're having trouble reading more than 2 bytes from BLE NUS. SDK 16. Software based in ble_app_uart but running custom board (no buttons, no LED), this is a ble peripheral...
Dear Sir or Madam,
i currently start developing with nrf52833 dev board. For the software examples from SDK16, how can I see, which version of software (pca10040/e, pca10056...
I need to pass a stream of data from raspberry pi 4 to PC through Ble. I can successfully build and run \examples\peripheral\usbd_ble_uart. It can communicate with my android...
Dear Nordic Folks,
Greetings! I see that nrfutil.exe dfu serial is used to update nRF52840 when using secure_bootloader_uart_mbr_pca10056.
Does Nordic provide c-code implementation...
Hi,
I am encountering some difficulties to undertand the context in which my sdk modules call back are called. I am using the uart part of ble uart nus example, and thus...
based on nRF SDK 16 radio (peripheral) example, in radio_config file, i set registers of TXPOWER, FREQUENCY, MODE, PCNF0, PCNF1 (and ADDR and CRC related registers) and also...
Hello, my company wants to get started with BLE direction finding. Maybe you can help me on how to setup some hardware. NRF52833 DK seems suitable but then I have no clue...
We are finishing up a project with the nRF52832 based on the Nordic Thingy. Most of what we want it to do are normal functions of the Nordic Thingy. It connects to a mobile...
Hi ,
Im trying to read and write data from QSPI w25q32jv chip, for which i get faulty data .
I have used this example : https://github.com/jimmywong2003/nrf52840-QSPI...
Hello,
I am very new to BLE and NRF and trying to understand what the best way would be to send data from one device to another
From the documentation and messing around...
Based on nRF5_SDK_15.3.0_59ac345 at NRF52810 development board, 1. Enable the watchdog with reload value = 2000, and feed it per 1000ms by app_timer 2. Initialize the FDS...
Hello,
I'm finishing migrating to the newest SDK from SDK 13.1. I'm having problems using the BLE_ADVERTISING_DEF macro, it doesn't compile.
The reason appears to be somewhere...
Hi,
I am fairly new to this, so please excuse my beginner mistakes.
I have a few coin battery sized nRF51 beacons (like this https://forum.mysensors.org/topic/6951/nrf5...
Hi teams,
I want to find GAP address of sending node after received message.
In client model callback, there is access_message_rx_meta_t argument, and I can get unicast...
I am using an nRF520 PCA10040 dev board with a nRF52832 module and I am trying to get the ble_app_uart_pca10040_s132 FW to run using the SES segger tool set. After about 1...
