I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
We are planning to use the nRF54LM20A, but we do not intend to implement USB in our design.
For the nRF52 series, the datasheet provides a reference schematic for...
Hello all,
Please let me know which module we can use for mesh networking for home automation project (lighting control through smartphone app),maximum how many devices...
Hi, we are currently implementing DECT NR+ mesh network as part of a thesis, where our one part of our plan was to implement full MAC layer (otherwise its just a full mesh...
Hi,
I'm trying to write a generic tool that lists the attribute table of a connected BLE Peripheral. For each discovered attribute I want to log to the console the attribute...
Hello,
I am trying to determine if it is possible to have those 3 stacks coexisting.
I have an iSP4520 chip, which includes an nRF52832 (BLE and Wirepas) and Semtech SX1262...
Hi,
We’re currently integrating the nRF54 series into a product we’re developing, and we’re using the reference schematic and layout as our guide.
While working through...
Zigbee Add-on (R23 1.2.1) doesn't support octect string attribute reporting which seems to be wrong.
I've found this topic that describes the same issue
and a workaround...
Hi Nordic Team,
We are developing a battery-powered cellular IoT device utilizing the nRF9161 SiP combined with the nPM1300 PMIC. Our primary goal regarding power management...
Hi,
We are updating an older platform with the nRF9151 on an add-on PCB.The platform has very limited processing power and buffer space.
The nRF9151 module with the...
I am using the Zephyr NVS Settings module. In some cases this happens: I try to save a value with ` settings_save_one ()`, which internally calls ` nvs_write ()`.
I debugged...
I'm running into a bit of an annoying situation every time i run ' west flash --build-dir ./build' in the command line. It rebuilds always after a successful build i set when...
Dear Nordic team,
I have a complex question. In my project I use components which operate at 2.25V as well as they expect 2.25V logic levels.
My idea is to use nrf52840...
Hello I am trying to implement AES Key Wrap on nrf54l15. For that i enabled ``` #necessary to get oberon_psa_wrap_key/oberon_psa_unwrap_key CONFIG_PSA_WANT_ALG_AES_KW=y #necessary...
Hello,
In nRF Connect for Mobile, custom UUIDs show up as unknown, making it difficult to identify them easily.
Is there a way to add custom UUIDs, as can be done for...
