Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I'm looking for the quiescent current and efficiency of REG0 DCDC under the conditions of 3.0v ≤ VDDH ≤ 4.2v, VDD=1.8v.
This is to determine if external regulation using...
I have a SparkFun Pro nRF52840 Mini that I am trying to flash with a simple Hello World program. I have the SDK setup in Visual Studios, created the custom board configuration...
I have this code developed for nRF5340.
Basically it scans for BLE advertisements based on the filters added and transmits the packets through UART.
Now for certain reasons...
Datasheet sampling rate is 100Ksps, but for me PPK2 always returns:
16384 bytes in ppk2_test.get_data() (one sample period)
4096 analog samples in ppk2_test.get_samples...
Hello Nordic,
I want to power down (at the lowest power consumption state as possible) all the peripherlas.
Already checked below ticket.
Below ticket also referenced...
hi,
I use softdevice s140 and nrf5_sdk_17.1.
I import time sync demo from here ( github.com/.../nRF5-ble-timesync-demo) to my project.
My first usage version:
* nrf52...
Hello,
I’m encountering an issue with my nRF52 device where it reboots during the flash_erase operation. Below is the relevant part of my code and the overlay configuration...
Hello all,
I'm using nrfx_spim_spis non_blocking sample to make my nRF5340 DK as SPI SLAVE.
I don't need SPI MASTER, so I delete the SPIM code.
But I found that I can...
Hi,
Is there any relationship between RTC peripheral and the system clock (which from DTC it looks like attached to rtc0)?
I'm trying to use PPI to generate a radio task...
I am looking for a solution of a multi-protocol controller for Linux host.
1. Coexistence of Wifi & BLE & Thread / Zigbee
The ble-coex / thread-coex example has the...
I'm trying to do a power analysis of an embedded device with a PPK2 and nRF power profiler and i'm running into an issue where i'm losing samples on longer capture periods...
I have a simple Thread joiner program. I am trying to join to a thread network created by my OTBR. Attached is my program. This program resets on call to otJoinerStart()....
Hi,
We use SDK 2.5.2 on a nrf9160. And have a hardware issue due to a too late update with the first boards. The GNSS LNA enable is wrongly connected to COEX1.
COEX0 is...
We are using eDRX to save power, but it seems like eDRX is not active always.
We currently use LTE_LC_EVT_EDRX_UPDATE callback to determine if eDRX is active. Is this...
