Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hey Nordic,
I am using
SDKv17.1.0
VSCODE as IDE
S140 as softdevice
Windows
Let me first insert my code snippet:
Here, NRF_LOG_INFO() function works, meaning...
Hello, I am trying to save data on an microSD card using SPI1. I am following the firmware in this discussion Working NRF9160 SD Card Example on SDK 1.9.0 . In addition I...
Hi! I used NRF CONNCECT to connect the Power Profiler Kit II, I opened the "Bluetooth Low Energer" app by mistake, and received a prompt to update the firmware. I chose to...
Hello Team,
We are looking to buy SOC which supports Bluetooth LE audio in a idea of developing broadcasting audio to multi devices.
Its understood that SOC RF5340 supports...
Hi Nordic engineer About the I2C SDA signal, when CLK voltage change then the SDA will occur skin needling，could you please helo explain it, I check the PCB latout, the I2C...
Hello ,
I am a firmware engineer in Taiwan ,
I already use nRF52820 to finish one case ( cheaper alcohol/acetone BT checker.)
Now ,the engineering stage is pre_production...
I am using SDK 14.2.0 with Segger IDE.
I am trying to configure timers and while my code does compile w/o errors the linker fails with message in the subject above.
To...
I see that nordi is working on wifi 6 .
When It will be available and on which platform ?
Is possible to have presentation on wifi 6 versus wifi 5 and BLE ?
Best Regards...
Hi
I want to use a Nordic NRF52840 to sniff and dissect a Digimesh network. Digi do not provide a sniffer or/and dissector for their products. There is no promiscuous version...
hello,
we are trying to use the stack guard module - obviously we want this to give well-behaved fault handling in the event that the stack gets too close for comfort. ...
Hi, I have a few questions regarding the modem module of the nRF9160 and considerations that might to be made when developing for it:
1. How does the modem determine which...
Hi,
We upgrade our SLM app from sdk 1.9.1 to sdk 2.0.0 and now when we try to look for GPS there is a reduction at the voltage from 3.3 to 2
what are we missing? what...
Hello Team,
This ticket is in continuation with Case ID: 292116. Based on last discussion I have taken more modem traces which are present in the attachment. Please ignore...
I've been working on porting a project to NCS using VS Code as my IDE. Now that NSC v2.0.0 is out, I wanted to move to that. I found the migration guide: https://developer...
I want to intercept some data in the RX (in section UART_RX_READY in uart_cb() as a command with arguments. And I do not want this data to be sent on the the BLE.
After...
