Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hello!!
I have explored extended advertising using both nRF5 SDK and nRF Connect SDK. Using nRF5 SDK, it is not possible to advertise 1650 bytes in an extended advertising...
Hello,
SDK17.2, keil5,nRF21540-DK
my project use i2c and spi, but got error:
Error: L6200E: Symbol SPIM0_SPIS0_TWIM0_TWIS0_SPI0_TWI0_IRQHandler multiply defined (by...
Hello,
SDK17.2, Keil5, nRF21540-DK,
when change DCCH to 3.3V as above codes in main first,
(1). the uart will can not work ,
(2). change pin to high voltage as follow...
I get some message from Nordic.I want to give my IQ sample to MQTT.i see that they give me information about a API of MQTT.
But i can't use it,can you give me the more information...
Hello !
What extra field need to be included ti MAXLEN calculation in case of Ieee802154_250Kbit radio ?
CRC , len ? I try to limit total amount of received bytes but...
Hi,
I have nrf52832 dK and know how to configure them in code.
I have studied BLE supports the LE 1M phy and LE 2M phys from BLE core specifications.
I know about the...
Hi devzone, I've had UART communication problems between nRF52 and a BG96 modem for a long time.
today I added a pull down resistance on the rx of the nRF52 and it works...
Good day,
I am currently developing with two NRF52840 DK boards, and I also have two NRF Dongles. On a dongle a sniffer for ZigBee. I am working with SDK 3.2. This is my...
Hi i want to make a low power delay ms (blocking) function for nrf52805 without softdevice and without NRFx, just writing to the registers.
The RTC1 events_tick never...
What is the recommended way to do DFU over Mesh in Zephyr? I saw DFU documentation in nRF5 SDK for Mesh v5.0.0 but not sure how this relates to Zephyr
Can you point me to...
Dear Sirs.
I bought thing91 and nrf9160.
I have connected the thingy 91 with nrf9160dk with prog/debug cable but I dont able to debug the application on the thingy91....
Hi,
I have this development board https://www.nordicsemi.com/Products/Development-hardware/nRF9160-DK . I would like to use development board as nb-IOT modem and other MCU...
I am just getting started with the Nrf52840 dongle and trying to flash a few examples from the SDK. I was able to flash the "blinky" example just fine using the programmer...
Hi,
I have been trying to interface GSM modem with nRF52840 using LPUART (nRF Connect SDK). I have used below pins for connections:
nRF52840 - GSM
P0.21 (TX) - RX
...
Hello,
Now I am developing firmware for nRF5284 DK, and the one of the requirement is the voltage keep in 2.1V.
Is there any possible I can modify the voltage to 2...
