I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hello,
I am using the nRF52832 WLCSP with the imprint "N52832 CIAAE0 2207A5", and my FICR reports a codepage size ox 0x400 and a code size of 0x100. This results in a...
Can the nrf7002 be set up to have both a STA virtual interface and an AP virtual interface at the same time?
From all the documentation it doesn't specify that only one...
I am using the Nordic Mesh Library with an ESP32 IDF-based application on the ESP32 side, and I am using ESP32 BLE Mesh. On the Android side, I have created a node to send...
Hi,
We are using the nRF52832 in a battery such that we have a 3V3 LDO configured to turn off under a certain battery voltage. Now during testing we have discovered that...
Hi,
I have made my own custom board with the nrf52811. Therefore I was using the nrf52dk.
I have made connection with my custom board and simply want to blink an led....
Hi,
I am using nRF54L15 DK and nRF21540 EK together. I am using the GPIO FEM mode. Below is my projconfig:
I notice that I cannot use 21540 EK in 54L15, the overlay...
Hi,
I am trying to pull up P0.08 as an enable pin for this switch TPS7A0518
I use the following code and verified on development board
However, when I move to...
Hi, we have a product in production and we are using the HWID which is accessible via this API https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/libraries/others/hw_id...
Hi Nordic teams,
There is have issue when I compile the V2.9.0. For more details
C:\ncs\v2.9.0\nrf\applications\nrf5340_audio>west build -b nrf5340_audio_dk_nrf5340_cpuapp...
Hi,
I m using SDK 2.9.0. After building and flashing my target board based on nRF5340, I get the above kernal panic error.
This is my .config.
and my prj.conf
Are...
Hello Everyone,
I am using nrf52832 and sdk 15.2 for BLE scanning and advertising. scanning and advertising is working parallel. this is controlled by other MCU over serial...
Hello,
I was able many times to download nrf52-ble-image-transfer-demo-master in to nRF52840 DK (PCA100156) and run a mobile application successfully.
Today I downloaded...
Hi ! I'm using nrf52 + SDK 17.1.0.
I found sd_mutex_acquire/ sd_mutex_release, which is great for locking variables that are set/get asynchronously. Next, I'd like to use...
