I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
I have successfully implemented the Azure IoT Hub sample on my nRF9160DK and added the ble scanning module. The kit is acting as a gateway, reading advertisements from a couple...
Hi ,
Device :- nrf52840
USB class :- CDC ACM
We are sending the ADC data (240 bytes at a time) to Host computer over USB (Full speed) and checking the received data...
Hi,
Using the Nordic secure bootloader for dfu OTA update, I am facing an issue causing the system to go under a condition where the bootloader is not any longer able to...
Hi. I'm trying to output frequency ( in the 1,250 Hz to 1,750 Hz range ) on GPIO. Each frequency should be outputted for 5ms time. For that, I use 2 TIMERs: one for 5ms counter...
Hi, we use nRF9160 and SDK 1.7.
in one of our applications, we need more than actually available flash. Now we have ~420kB for application - because we use MCUBoot and dual...
As title says, I cannot get anything to change in autoconf.h after changing the corresponding value in prj.conf using nRF Connect samples. I have tried both Project-->Reload...
I have made custom mobile app and I am trying to connect to it. When using nrf Connect app it is connecting properly
but i want to connect to my mobile app . it is connecting...
Hi, I'm trying to run the Openthread Cli sample on my nrf5340 DK, and it looks like that part is doing fine. But if I want to test the thread network with Putty I don't get...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
Hi,
I'm trying to see how a BLE packet is formatted and sent from a Thingy:52 and I know the preloaded code on the THingy:52 has that functionality, can you direct me to...
Hi, do you have plans to test the nrf52805 at 105 degC or higher, similar to nrf51822 Extended Industrial Temperature range document
We will probably run the NRF52805 at...
I have created zigbee network using nordic dk board, i am trying to fetch all the active nodes in the network using zdo mgmt_lqi cli and i am getting those details but when...
Hi, What is in your opinion the best way to handle device reset after the Zigbee connection fails?
I want to archive behavior like so: after connection fails sleep for 10...
Hello,
I am working on a project which requires 2 FTDs and 2 MTDs (Sensor and Actuator) in a Thread Network.
We are using nRF52840 dongle as FTDs and arduino nano sense...
after connect v3.7.1 programer v1.4.11 for a nrf9160dk I get an error "Error: Error occured when get library info. Errorcode: CouldNotOpenDevice (0x4) Lowlevel error: INVALID_OPERATION...
