My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
Hello, i I am designing a prototype, the goal is to be able to control a small engine. This engine will be activated when a message is received in MQTT. I currently succeeded...
Hello, I developed for my customer, a ZigBee coordinator in last 2019, using nRF5 SDK for Thread and Zigbee v3.2.0. I have now two questions: - is ZigBee 3.0 supported by...
I'm currently working on the nrf52832_qfax_dcdc pcb after adding a few components. I need to route to pins p0.22, p0.23 SWDIO and SWDCLK but am unable to route away from the...
Hello,
I noticed that publishing mqttsn messages with a payload larger than ~255 bytes caused an error in the mqttsn library. I think the problem comes from this definition...
I am developing an app for the 51822 with 16KB RAM, which is supposed to integrate the buttonless DFU.
I have attached the whole hex of the merged application+softdevice...
Hi Nordic Tech Support,
Our company is evaluating nRF5340 for future project. I have brought one nRF5340 DK, and I am following the online guide to build and program the...
Setup:
periheral: RF52840, S140 softdevice (SDK 15.3)
central: for test/development: laptop with Linux and BLE adapter build in, and/or Raspberry Pi, using Python testing...
I'm using the nRF5340 (currently nRF5340DK with custom hardware following shortly) and NCS 1.6.0. I'm working on a project that needs at least two UARTs and one SPI master...
Hello,
In nRF5340 project, I have two projects, one is for net core, the other is for app core. I use SEGGER to build these two projects, flash the images into the development...
I am using the nrf9160 for an OTA firmware update application. I initially executed the fota download file from the http_application_update sample project in it's default...
Hi,
I have the driver code for SPI based external NOR flash. Now I want to port the filesystem (FAT filesystem) for the same. I am using SDK v16.0 and nRF52832. Please tell...
Is there a script with which I can flash a nrf52 directly over Bluetooth. I tried to use "nrfutil.exe dfu ble -ic NRF52 -a mac_address" but it requires a board to be connected...
Hi,
In oner of new project, we planned to use nRF 52833 with BLE mesh implementation.
We are planned to use IAR 8.50.1. We have downloaded both nRF SDK(17.0.2) and mesh...
I try to use 52832 as a frequency meter to measure the bluetooth central frequency to do crystal trimming.
The target is a CW(continous wave) signal, like 2441MHz,which...
