Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi ,I'm using nRF52832 Bluetooth DK and (SDK15.3.0) , I am trying to switch between beacon mode and uart mode without the need to reset button , e.g with reset button from...
Hi,
using a stock nRF52840 dongle and willing to enter bootloader (same as pushing the relevant button on the dongle) from app. How can that be done, using stock bootloader...
Hello,
I am using custom board with nRF52810 (QCAA, QFN32), SDK14.2, and softdevice S112 v5.1.0/S132 v 51.10 according to the compatability matrix. I am programing the board...
I have a question about LE Secure Connections (LESC).
As an example, consider the following behavior. 1. "Device A" scans as "Central". 2. "Device B" advertises as "Peripheral...
I have a question about "Importing Keil projects".
I want to run "ble_app_multirole_lesc (SDK V14.2.0)" using "SEGGER Embedded Studio". However, there is no project file...
Hello,
Currently, I have a product with the nrf52832 SOC and my customer wants to know its life-cyle.. (approximately)
just to take into account possible replacements...
I have a question about LE Secure Connections(LESC).
Is it possible to pair with multiple devices in multi role operation? I am considering the following connection. ・Peripheral...
I'm using ble_app_uart_c example with NRF52840.
And i want to read the beacon device id( 8 byte ) at Central(nrf52840).
The ADDR value could be verified through the questions...
Hi, i'm using nrf52832 uploaded ble_app_beacon example.
I want nrf52832 to work as a beacon and as a nfc tag.
Thus, I added some nfc example code. nfc_t2t_lib.h also...
I'm investigating a failure in 2 devices. The devices are immediately failing in application start-up due to fds_init failure. I tracked the failure back to fds pages_init...
Hi,
I could not find the logic for spi_xfer_done flag (main.c) that is being updated after SPI transfer is done in the SPI example from SDK 15.3.0.
There is no particular...
In light switch example, I am trying to implement relay feature. I used nRF5_SDK_15.2.0_9412b96, nrf5_SDK_for_Mesh_v3.0.0_src.
When compiled light_switch_client_nrf52840...
Hi,
I am using modem version 0.7.0-29 alpha modem firmware. ( I have also checked with 0.6.8-131 version )
I have already done MQTT connection with Azure IOT hub and...
I need to increas the speed using the UART ove BLE application.
I try to add new characheristics to the Nordic UART Service.
I have added the UUID for this new charactheristic...
Hello,
I would like to get AT Command Sample to work on nRF9160. I erased the module using Programmer software "erased all" and then loaded Secure Boot sample, then updated...
